 2.7 CIS to Carbs - how much HP loss? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Scott S |
 Jul 2 2009, 03:15 PM
Post
#1
|
|
Small Member  Group: Members Posts: 1,698 Joined: 30-April 03 From: Colorado Member No.: 633  |
Hi All -
Got a line on a rebuilt 2.7 out of a 1977 911S. It is 100% complete including the full CIS system. What kind of power loss would I experience if I stripped off the CIS and went with carbs? The motor is only 165hp to begin with... Thanks! Scott S |
   |
 
|
  |
Replies
| carr914 |
Jul 3 2009, 06:15 AM
Post
#2
|
|
Racer from Birth Group: Members Posts: 124,877 Joined: 2-February 04 From: Tampa,FL Member No.: 1,623 Region Association: South East States  |
QUOTE(pcar916 @ Jul 3 2009, 01:13 AM)  When I bought my car it had a 2.7L motor built up to Bruce Andersen's 911 Performance Handbook spec's with 40 IDA carbs, headers, the proper cams, shuffle-pinned... everything except the Euro pistons. It had CIS. You can't have carbs and CIS. The fact that you talked about the jets means you had carbs |
|
|
|
| pcar916 |
Jul 3 2009, 07:45 AM
Post
#3
|
|
Is that a Lola? Group: Members Posts: 1,523 Joined: 2-June 05 From: Little Rock, AR Member No.: 4,188 Region Association: None 
|
QUOTE(carr914 @ Jul 3 2009, 04:15 AM) QUOTE(pcar916 @ Jul 3 2009, 01:13 AM) When I bought my car it had a 2.7L motor built up to Bruce Andersen's 911 Performance Handbook spec's with 40 IDA carbs, headers, the proper cams, shuffle-pinned... everything except the Euro pistons. It had CIS. You can't have carbs and CIS. The fact that you talked about the jets means you had carbs That's correct. I should've said "... it had CIS pistons instead..." Thanks |
|
|
|
Posts in this topic
Scott Schroeder 2.7 CIS to Carbs - how much HP loss? Jul 2 2009, 03:15 PM
brant Scott,
I heard about that motor
seemed like a re... Jul 2 2009, 03:20 PM Cupomeat I cannot support the following with empirical evid... Jul 2 2009, 03:21 PM turboman808 From what I have seen on graphs you get peaks and ... Jul 2 2009, 03:46 PM carr914 I would think that you would H.P. & Torque wit... Jul 2 2009, 04:43 PM 9146986 Why not just keep the CIS? Jul 2 2009, 10:11 PM pcar916 When I bought my car it had a 2.7L motor built up ... Jul 2 2009, 11:13 PM GeorgeRud If you don't have it, I would get Bruce Anders... Jul 2 2009, 11:29 PM ahdoman If the CIS is intact and working stick with it. Yo... Jul 3 2009, 12:10 AM Project 6 Wayne at Pelican claims to have installed a CIS mo... Jul 3 2009, 07:50 AM J P Stein I know a few folks that run Webers on an otherwise... Jul 3 2009, 08:51 AM Gint I'd probably just use the CIS. But if you buy... Jul 3 2009, 08:53 AM scotty
I know a few folks that run Webers on an otherwis... Jul 3 2009, 10:28 AM naro914 I have a 2.7 in Huey at the moment, with Webers. I... Jul 4 2009, 10:56 AM Mountain914 Just want to throw this out there - since the titl... Jul 4 2009, 11:44 AM
J P Stein
Just want to throw this out there - since the tit... Jul 4 2009, 01:38 PM ArtechnikA
A good illustration of the possibilities of the 2... Jul 4 2009, 02:02 PM J P Stein
A good illustration of the possibilities of the ... Jul 4 2009, 04:02 PM ArtechnikA
Yeah,yeah, some folks go all gaga over the MFI se... Jul 4 2009, 05:31 PM naro914 This is a good discussion....
I have carbs. I lik... Jul 4 2009, 04:14 PM J P Stein
This is a good discussion....
I have carbs. I li... Jul 4 2009, 07:12 PM 9146986 As long as the carbs are optimized for the engine,... Jul 5 2009, 11:18 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 10th May 2025 - 04:20 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.