 Just when....., Fuching fuel tank! My 914 hates me! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Pat Garvey |
  Jul 12 2009, 08:31 PM
Post
#1
|
|
Do I or don't I...........?  Group: Members Posts: 5,900 Joined: 24-March 06 From: SE PA, near Philly Member No.: 5,765 Region Association: North East States  |
After spending countless hours lubing wire harnesses to get them thru the side marker/signal light boots, cussing & bitching, I thought about looking with flashlight into the gas tank. Bad thing to do!
I had drained the tank 6 months ago & took the pseudo gas to a shop that heats the floor with it in winter. Cool! Problem complete. Replaced lotsa fuel lines thereafter. Try to open the gas cap, doesn't want to. Finally, with "persuasion", the gas cap pops off. First thing I'm faced with is severe rust in the filler neck! Shine a light into the tank, and I see about another gallon of fuel, but looks like it's full of rust! Rust must have plugged the strainer. Like I need aother project, but what sould I do? Looks like the tank has to come out, be steamed & sealed., right? Who do I go to in SE Penna to get this done? Pat |
   |
 
|
  |
Replies
| tod914 |
Jul 13 2009, 09:32 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 3,755 Joined: 19-January 03 From: Lincoln Park, NJ Member No.: 170 |
Pat there is a place out in Allentown that does gas tanks. They were reckomended by Bill Hirsch (gas tank sealant company here in NJ) I'm not sure how far away that is from you. But Mike's offer sounds like a good one. Let me know if you want me to search for the number. Too much of a PIA to do yourself if you can find someone local to do it for you. I found an excellent match for the paint too. Might want to bake it on to insure it's resistant to gas. http://www.hirschauto.com/
I'll get you the paint info tomorrow when I'm not so tired. |
|
|
|
Posts in this topic
Pat Garvey Just when..... Jul 12 2009, 08:31 PM
r_towle
After spending countless hours lubing wire harnes... Jul 12 2009, 09:06 PM
Pat Garvey
After spending countless hours lubing wire harne... Jul 13 2009, 07:08 PM PanelBilly I thought all we needed to do was use the POR gas ... Jul 13 2009, 08:05 PM Dr Evil
I thought all we needed to do was use the POR gas... Jul 13 2009, 08:34 PM Dr Evil I can still help you, Pat. There is a shop about 2... Jul 13 2009, 08:32 PM Pat Garvey
I can still help you, Pat. There is a shop about ... Jul 15 2009, 08:00 PM Dr Evil
I can still help you, Pat. There is a shop about... Jul 15 2009, 09:17 PM jcd914 I think it is a choice of "Do It Yourself... Jul 13 2009, 08:33 PM r_towle I am old school
I boiled it out, painted the outsi... Jul 13 2009, 09:38 PM jim_hoyland If a 914 is gonna sit for a while, should the gas ... Jul 13 2009, 09:54 PM Dominic I did mine with the KBS products, very nice result... Jul 14 2009, 07:53 AM RobW Is the rub rust patch on the outside typical? I th... Jul 14 2009, 11:50 PM kwales I've seen rust pateches on the outside of the ... Jul 15 2009, 10:25 AM BarberDave :trophy:
Jim H. :
As to storing a ... Jul 15 2009, 10:41 AM RobW
:trophy:
Jim H. :
As to storing a... Jul 15 2009, 01:34 PM Pat Garvey I just want to post a warning from my experience. ... Jul 15 2009, 08:16 PM r_towle A few times.
Remove all the top stuff.
From the pa... Jul 15 2009, 09:00 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th July 2025 - 11:43 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.