Steve's unending Progress thread, Air compressor setup recommendations Options

[stephenaki]

OK, this will be the thread that I keep updated as I make progress. I showed up at 0800 at Christoph's place and he was ready for me with a not so glamorous chunk of metal that is my cars heart and soul.

With a little assistance, we loaded it into my Toyota Sienna, not quite I envisioned a mini-van for, and I was headed back to the house. Upon getting home I had to first make coffee then clear out some space in my tiny German garage. So that everyone has a frame of reference to the area that I am working in I have enclosed this lovely 4x6 glossy of my garage in Germany.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747638.1.jpg)

And, for those of you not familiar with the Toyota Sienna, a shot of the engine in the back of the van. There's a lot of room back there for the motor but, it is awkward to get in and out of when loading a motor.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747639.2.jpg)

Now to summarize what was accomplished on the 4th of July, engine brought home, tin, impeller and housing, exhaust, cylinder head and cylinders removed. I had difficulty removing the impeller hub. OK, I didn't get it removed, will need a puller and I don't have one unless anyone can give me any ideas how to get it off without a puller.

Now for the requisite pictures of the motor unmolested.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747639.3.jpg)
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747640.4.jpg)

Now based on the initial tear down two problems presented it self first the primary issue with a lack of compression...HOLY SHIT!!! Here is what I found.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747641.5.jpg)
(IMG:style_emoticons/default/blink.gif) (IMG:style_emoticons/default/blink.gif) (IMG:style_emoticons/default/blink.gif) (IMG:style_emoticons/default/blink.gif)
Now the cylnder itself was not pitted, it had a build up of corrosion but otherwise in good condition. So I was thinking, maybe I can just clean hone and replace the piston. Well that thought went out the window when I pulled the cylinder directly opposite to it. As you can see by the photo, problem #2.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747642.6.jpg)

More importantly, where did that piece of metal go? An initial look behind the piston shows a knick in the inner portion of the crankcase.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747642.7.jpg)

I will see if there is more significant damage when I split the case; so it begins and were off to a rocket start here at the 914 follies! Stay tuned for the next exciting episode of "never buy a car sight unseen" later in the week! (IMG:style_emoticons/default/happy11.gif)

Gonna go shower and start working on the motor some more. Plan is to have it completely torn down befor the end of this weekend. I will load up some pictures to my photo bucket album and post the link a bit later.

[stephenaki]

Well ladies and gentlemen, it's home. (IMG:style_emoticons/default/piratenanner.gif) Christoph had to do some major work before it could be released and I am not sure I want to see the bill!

So, what else did he do? Let see.

- Replace the rotors and bolts on front wheels
- Replace the right front strut and shock
- Replace the right front brake caliper
- Replace the brake master cylinder
- Replace the brake proportioning valve
- under body welds and various places
- electrical work, did I mention the PO totally jacked up the wiring harness and electrical connections? Christoph said that they had a hard time because the wiring didn't match the diagram!
- Replaced all 5 wheels and rims, TUV wanted a more original rim for the historical cert so he gave me 4 new/used pegrini rims. Still got the old ones, gonna sell em on ebay as they will fit a VW beetle.

So what is left to do?
- Rear trailing arm bushings need to be replaced eventually. Anyone got a set of used ones I can send for rebuild?
- I seem to have a minor oil leak I think in the front seal, need to track it down.
- leak in targa top needs to be identified and fixed.

She runs OK, little rough when she is cold and I am pretty sure I will need to rebuild the tranny eventually but for now she runs and is registered. Now I just have to mortage a house to pay for the German labor costs! Will get a picture this weekend and post.