Steve's unending Progress thread, Air compressor setup recommendations Options

[stephenaki]

OK, this will be the thread that I keep updated as I make progress. I showed up at 0800 at Christoph's place and he was ready for me with a not so glamorous chunk of metal that is my cars heart and soul.

With a little assistance, we loaded it into my Toyota Sienna, not quite I envisioned a mini-van for, and I was headed back to the house. Upon getting home I had to first make coffee then clear out some space in my tiny German garage. So that everyone has a frame of reference to the area that I am working in I have enclosed this lovely 4x6 glossy of my garage in Germany.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747638.1.jpg)

And, for those of you not familiar with the Toyota Sienna, a shot of the engine in the back of the van. There's a lot of room back there for the motor but, it is awkward to get in and out of when loading a motor.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747639.2.jpg)

Now to summarize what was accomplished on the 4th of July, engine brought home, tin, impeller and housing, exhaust, cylinder head and cylinders removed. I had difficulty removing the impeller hub. OK, I didn't get it removed, will need a puller and I don't have one unless anyone can give me any ideas how to get it off without a puller.

Now for the requisite pictures of the motor unmolested.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747639.3.jpg)
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747640.4.jpg)

Now based on the initial tear down two problems presented it self first the primary issue with a lack of compression...HOLY SHIT!!! Here is what I found.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747641.5.jpg)
(IMG:style_emoticons/default/blink.gif) (IMG:style_emoticons/default/blink.gif) (IMG:style_emoticons/default/blink.gif) (IMG:style_emoticons/default/blink.gif)
Now the cylnder itself was not pitted, it had a build up of corrosion but otherwise in good condition. So I was thinking, maybe I can just clean hone and replace the piston. Well that thought went out the window when I pulled the cylinder directly opposite to it. As you can see by the photo, problem #2.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747642.6.jpg)

More importantly, where did that piece of metal go? An initial look behind the piston shows a knick in the inner portion of the crankcase.
(IMG:http://www.914world.com/bbs2/uploads_offsite/i273.photobucket.com-7987-1268747642.7.jpg)

I will see if there is more significant damage when I split the case; so it begins and were off to a rocket start here at the 914 follies! Stay tuned for the next exciting episode of "never buy a car sight unseen" later in the week! (IMG:style_emoticons/default/happy11.gif)

Gonna go shower and start working on the motor some more. Plan is to have it completely torn down befor the end of this weekend. I will load up some pictures to my photo bucket album and post the link a bit later.

[stephenaki]

OK, so I put her on the lift today to find the oil leak. Well, I am pretty sure I have a slight main seal leak as a drop of oil accumulated on the bottom of the fan shroud. I am also getting a good amount from the pushrod tubes on the driver side once she has been moving and is warmed up. I didn't see a lot when she was running and up in the air but when I got home from a long drive you could see a good amount on the ground where the push tubes are located.

So, how easy is it to pull the tubes and change the seals without dropping the motor? Looks a little tight in there from where I was looking up. I know that it sounds sacrilegious but would using the Mittelmotor technique of just using high heat auto seal/calk in there do the trick? Looking for some suggestions because I don't think it will sell if she has a big oil leak problem. A small bit is fine but this isn't what I consider a small bit.

I also think I have an exhaust leak on the drivers side, I took a video and I'll try to figure out how to embed the video after I get back from cleaning my bike.

I did manage to fix the rear view mirror and side mirror thanks to a very informative write up on how to tighten up the side view mirror in the Lapawuli section. I also got the passenger side door handle working again but I don't think the key matches the lock because I can't lock the doors. I will see if there is a thread on this in the forum later.

Gustl has been very helpful in translating and making suggestions for the add to sell the car and I will post it to the 914freunde site later today. Will post some pictures and the video when I get back later.