 Removing trailing arm bushings, what a pain |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| tradisrad |
 Aug 21 2009, 09:03 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 985 Joined: 11-September 06 From: San Mateo, CA Member No.: 6,815 Region Association: Northern California  |
I purchased Elephant Racing poly bronze bushings for the rear. I spent a ton of time and several broken drill bits removing the stock rubber from one trailing arm.
This task was a big PIA. Is there another way, for those who don't have a 20-ton press, to remove these bushings? Any advice is appreciated. |
   |
 
|
  |
Replies
| tradisrad |
Aug 21 2009, 09:25 AM
Post
#2
|
|
Senior Member Group: Members Posts: 985 Joined: 11-September 06 From: San Mateo, CA Member No.: 6,815 Region Association: Northern California |
yes, I applied heat and had them smoking. Worked great for the front, but not so great for the rears I am working on.
The elephant set comes with special shafts, so I am not worried about getting those hot. I did not want to use heat on the painted surface 'cause I don't want to repaint, but it's too late now! |
|
|
|
Posts in this topic
tradisrad Removing trailing arm bushings Aug 21 2009, 09:03 AM
jaxdream Have you tryed heating with a propane tourch to me... Aug 21 2009, 09:10 AM McMark Here's what I do. They come out smoothly. No... Aug 21 2009, 11:19 AM
kconway
Here's what I do. They come out smoothly. N... Aug 21 2009, 12:14 PM
jaxdream
Here's what I do. They come out smoothly. N... Aug 21 2009, 12:21 PM tradisrad McMark, thanks I'll give that a try! I... Aug 21 2009, 11:53 AM J P Stein Fire is your friend....unless you live in CA. :D Aug 21 2009, 12:02 PM ChrisNPDrider Yes, they are a pain to get out! I found that ... Aug 21 2009, 12:02 PM sean_v8_914 a press works best Aug 21 2009, 12:15 PM tradisrad McMark: :worship: You saved me hours on the second... Aug 22 2009, 09:50 AM SKL1 Now what?
Pushing out the hubs with a 12 ton pre... Mar 24 2013, 06:37 PM bandjoey WAtch this for the hubs and bearings:
http://www.... Mar 24 2013, 06:42 PM SKL1 Figured Eric would have the answer!
Bet I... Mar 24 2013, 07:23 PM SKL1 Installing rear bearing video won't work- hope... Mar 24 2013, 07:35 PM Eric_Shea Do you have a press? Mar 24 2013, 07:53 PM SKL1 Yep a 12 ton HF that looks like the one in one of ... Mar 25 2013, 05:41 AM 02loftsmoor I looks like you came from cold country, is there ... Mar 25 2013, 09:36 AM Eric_Shea
I simply press the shafts out. As follows:
1. ... Mar 25 2013, 04:05 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 4th June 2025 - 01:49 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.