 Valve cover gasket glue, what do you use |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Krieger |
 Dec 18 2010, 08:54 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 4,808 Joined: 24-May 04 From: Santa Rosa CA Member No.: 2,104 Region Association: None 
 |
I went in asking for Gask-a-cinch and the oldtimer at my favorite flaps told me this is the stuff to have: a tube of 3M Super Weatherstrip and Gasket Adhesive. Any experience with this stuff? What do you fellas use?
|
   |
 
|
  |
Replies
| charliew |
Dec 18 2010, 09:14 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,363 Joined: 31-July 07 From: Crawford, TX. Member No.: 7,958 |
I always used the 3m but it is a job putting on new gaskets and cleaning the 3m off. What about using a silicon adhesive on the valvecover side? I would think it would clean off a lot easier.
|
|
|
|
Posts in this topic
Krieger Valve cover gasket glue Dec 18 2010, 08:54 PM
Jake Raby The 3m works well.. Just use it on the valve cover... Dec 18 2010, 09:01 PM
Krieger
The 3m works well.. Just use it on the valve cove... Dec 18 2010, 09:18 PM quadracerx Yea it works REALLY GOOD....used to call it ... Dec 18 2010, 09:15 PM mrbubblehead i use gask-a-cinch on the cover side. dry on the h... Dec 18 2010, 09:23 PM Krieger
i use gask-a-cinch on the cover side. dry on the ... Dec 18 2010, 09:26 PM mrbubblehead
i use gask-a-cinch on the cover side. dry on the... Dec 18 2010, 10:21 PM sww914 Contact cement on the cover side, dry on the head ... Dec 18 2010, 09:37 PM Jake Raby I didn't have to change the gaskets in 8 years... Dec 18 2010, 10:15 PM Vacca Rabite I use the 3M stuff too. A very thin smear on the ... Dec 19 2010, 09:20 AM StratPlayer http://www.kedo.com/base_com/21053.html Dec 19 2010, 11:10 AM davesprinkle We're talking about the cork seals, right? Wh... Dec 19 2010, 11:16 AM Bartlett 914
We're talking about the cork seals, right? W... Dec 19 2010, 12:59 PM Vacca Rabite
We're talking about the cork seals, right? ... Dec 20 2010, 06:52 AM Pat Garvey
We're talking about the cork seals, right? W... Dec 19 2010, 07:43 PM NC_Colfax I used a couple of drops of super glue. Worked ver... Dec 19 2010, 07:38 PM stugray I will probably get flamed for this, but here is w... Dec 20 2010, 07:07 AM Vacca Rabite But, how did you check your valves?
Zach Dec 20 2010, 08:02 AM stugray The RTV was allowed to dry before replacing the co... Dec 20 2010, 09:08 AM Cap'n Krusty
I went in asking for Gask-a-cinch and the oldtime... Dec 20 2010, 10:38 AM underthetire Gasgacinch for me. Started using it when I split d... Dec 20 2010, 11:49 AM Jake Raby Anyone who has ever seen an engine fail only becau... Dec 20 2010, 01:30 PM Drums66 ...I use engine earl...No prob,No issue's :D
... Dec 20 2010, 01:32 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 4th July 2025 - 07:52 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.