 end cap install, installing window/door end caps late model |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| eastbay851 |
 Dec 21 2010, 01:14 PM
Post
#1
|
|
Newbie  Group: Members Posts: 39 Joined: 29-November 10 From: california Member No.: 12,438 Region Association: None  |
hi all. i have a bit of a modified 75.... 13b rotary, 911 front end, scraped and filled, camera-monitor system in place of rear views and i am now stumped.... silly i know. after re-upholstering the door panels i went to install the new (914rubber) door/window end caps and cannot do it. the window glass is in the way of the inside screw. do i have to drop the window assembly to install these 2 insignificant widgets? you could probably sense my frustration. this is like traveling across the pacific to finally getting to hawaii and the tide is out so you can t dock and you have to walk the last 200 yards(meters for you euros.) thanks for your help.
|
   |
 
|
  |
Replies
| dr914@autoatlanta.com |
Dec 21 2010, 05:17 PM
Post
#2
|
|
914 Guru Group: Members Posts: 7,894 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
Mark hit it. No reason to drop anything. You can roll down the window and access the inner channel screw with a magnetic phillips screw driver through the hole in the fuzzy window channel. It is easy and should take ten minutes (if you are slow) to change both!!!!!
Of course the small outer screw is a piece of cake. QUOTE(eastbay851 @ Dec 21 2010, 12:14 PM)  hi all. i have a bit of a modified 75.... 13b rotary, 911 front end, scraped and filled, camera-monitor system in place of rear views and i am now stumped.... silly i know. after re-upholstering the door panels i went to install the new (914rubber) door/window end caps and cannot do it. the window glass is in the way of the inside screw. do i have to drop the window assembly to install these 2 insignificant widgets? you could probably sense my frustration. this is like traveling across the pacific to finally getting to hawaii and the tide is out so you can t dock and you have to walk the last 200 yards(meters for you euros.) thanks for your help. |
|
|
|
Posts in this topic
eastbay851 end cap install Dec 21 2010, 01:14 PM
76-914 IIRC, you can loosen the regulator enough to drop ... Dec 21 2010, 03:44 PM r_towle no need to drop it.
Need less coffee, better light... Dec 21 2010, 05:08 PM
eastbay851
no need to drop it.
Need less coffee, better ligh... Dec 21 2010, 05:20 PM markb A slightly magnetic screwdriver helps a lot, too. Dec 21 2010, 05:13 PM Mikey914 If you can post some pictures, maybe something dif... Dec 21 2010, 05:21 PM eastbay851 look doc, i m sure you are the best ever but do yo... Dec 22 2010, 09:05 AM windforfun I cut perfect rectangular slots in mine so I would... Dec 22 2010, 11:47 AM RobW Its a nice piece. I installed these on mine after ... Dec 22 2010, 12:20 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 7th June 2024 - 02:21 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.