 Ok I got my Trans out..., Now what? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| rwilner |
 Dec 24 2010, 02:12 PM
Post
#1
|
|
No Ghosts in the Machine  Group: Members Posts: 953 Joined: 30-March 10 From: Boston, MA Member No.: 11,530 Region Association: North East States  |
I got my trans out of the car, packed, and shipped down to Richard Casto at Blue Sky for a rebuild.
   My question is, what other work should I do now, or parts should I replace? the obvious stuff -- - new CV joint bolts (8) - paper cv joint gaskets - trans fluid (duh) the cv boots look to be in good shape. Is there anything else obvious I should be doing with the trans out of the car? thx Rich |
   |
 
|
  |
Replies
| montoya 73 2.0 |
Dec 24 2010, 02:23 PM
Post
#2
|
|
Lack of consideration to others, and Selfish! Group: Members Posts: 1,791 Joined: 27-October 04 From: Paso Robles, Ca. Member No.: 3,016 Region Association: Central California |
Check and replace with all new Shift bushings, Also new Cone screws (very important)! Maybe even check your clutch and cable? Oh and your throw out bearing.
|
|
|
|
Posts in this topic
rwilner Ok I got my Trans out... Dec 24 2010, 02:12 PM
Dr Evil Drew hit it on the head. Also, you do not need the... Dec 24 2010, 02:50 PM
Racer Chris
... you do not need the paper CV gaskets. They sh... Dec 27 2010, 12:13 PM Dr Evil Oh ya, read the 31 pages of notes below to find li... Dec 24 2010, 02:55 PM rwilner Thanks guys. Shift bushings and clutch cable are a... Dec 24 2010, 03:01 PM Dr Evil You should be good to go :thumbsup: Dec 24 2010, 03:18 PM jim912928 Transmission mounts while it's out if they are... Dec 24 2010, 03:42 PM rwilner thanks Jim, PO replaced them with solid ones.
Sou... Dec 24 2010, 03:43 PM Dr Evil Solid ones are not friendly for street use. Have y... Dec 24 2010, 04:31 PM rwilner Hey Dr
My car rattles my teeth over bumps -- PO se... Dec 24 2010, 06:07 PM montoya 73 2.0 I just remembered the 2 alignment roll pins! T... Dec 24 2010, 04:48 PM Dr Evil Richard should notice that and correct it if there... Dec 24 2010, 04:52 PM montoya 73 2.0 :thumbsup: Dec 24 2010, 04:53 PM Dr Evil Yup, GPR can hook you up as well. They are my pref... Dec 24 2010, 07:53 PM Richard Casto
I got my trans out of the car, packed, and shippe... Dec 24 2010, 08:23 PM bigkensteele
I got my trans out of the car, packed, and shipp... Dec 26 2010, 10:51 PM Richard Casto
[quote name='rwilner' post='1409463' date='Dec 2... Dec 27 2010, 06:40 PM Cevan Don't forget new Schnorr washers. Dec 24 2010, 09:03 PM rwilner
Don't forget new Schnorr washers.
Thanks Ce... Dec 25 2010, 08:12 AM Richard Casto
Don't forget new Schnorr washers.
Thanks C... Dec 25 2010, 09:07 PM Dr Evil I always have a designated box for each transmissi... Dec 25 2010, 09:23 PM type47 CV bolts drilled for safety wire... Dec 26 2010, 02:28 PM Dr Evil Can I get an amen?
RJMII does these now :) Dec 26 2010, 02:59 PM rwilner
Can I get an amen?
RJMII does these now :)
ok,... Dec 26 2010, 10:19 PM r_towle I second getting new washers...
Also, get a can of... Dec 26 2010, 05:29 PM rwilner
stop trying to spend money.... :)
Says the guy... Dec 26 2010, 06:46 PM Cap'n Krusty Replace that inop thermostat ........................ Dec 26 2010, 10:36 PM rwilner
Replace that inop thermostat ....................... Dec 27 2010, 08:46 AM Dr Evil In my experience, high temp silicone has always wo... Dec 27 2010, 12:15 PM Racer Chris How long do you have to wait to drive the car?
Wit... Dec 27 2010, 12:21 PM Dr Evil :P Dec 27 2010, 12:30 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 3rd July 2025 - 11:21 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.