 Need a little help- 914 project., Hell Hole- repair or walk? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| C.Plavan |
 Jan 1 2011, 01:11 PM
Post
#1
|
|
Newbie  Group: Members Posts: 37 Joined: 27-March 05 From: Clovis, California Member No.: 3,825 Region Association: None  |
I'm a 914 newbie, but not a 911 newb. I was going to buy this car for a race car project. I showed the pictures to a fellow 914 racer and he had some concerns about the Hell Hole area. I figured I could just weld over the spot to strengthen, but from what I understand it could be more than just the hole that shows damage.
So after doing some more research, I'm even more concerned. I asked the seller to send me more pictures of this area from the top, bottom, and from the wheel well area. Just looking for some more guidance, should I pass on it and look for a different car? I'm thinking it may not be worth the headache. Your thoughts?  |
   |
 
|
  |
Replies
| C.Plavan |
Jan 1 2011, 05:35 PM
Post
#2
|
|
Newbie Group: Members Posts: 37 Joined: 27-March 05 From: Clovis, California Member No.: 3,825 Region Association: None |
QUOTE(Spoke @ Jan 1 2011, 03:08 PM)  This car looks like an east coast rust bucket. The passenger long is gone on the outside and replaced by a piece of steel. The firewall is rusted along the entire edge of the floor. This car should be really cheap to be worth it. Are you trying to save money and get a car to work on rust-wise, or do you want a 914 to drive? Very true, after seeing those rockers, there was a reason those were put on. Thanks for confirming my suspicions. QUOTE(kg6dxn @ Jan 1 2011, 03:10 PM) Based on the last pictures... Buy a new tub and strip the good parts off that one. Someone has done major work to the longs and not done it correctly. I also see parts chopped off in the engine bay. You will spend way too much making this one right. Buy another roller with less rust. I have a similar car that I'm cutting up due to rust like yours. Your passenger long looks like a hack job, although it may be structually sound. Again, thanks for all this- I appreciate all the help and insight. QUOTE(Joe Sharp @ Jan 1 2011, 03:20 PM) Post #21 (IMG:style_emoticons/default/w00t.gif) (IMG:style_emoticons/default/mad.gif) It looks to me like that car has about 1000 pounds of scrapmetal. LOL not good for a race car! Brant- You have a PM |
|
|
|
Posts in this topic
C.Plavan Need a little help- 914 project. Jan 1 2011, 01:11 PM
silver74insocal :wttc: more experienced people will chime in soon... Jan 1 2011, 01:45 PM MrHyde You California peoples get all the good cars ... Jan 1 2011, 01:45 PM detoxcowboy California Car? How was it stored? Empty lot? Or a... Jan 1 2011, 01:46 PM JRust Really depends how bad it is below that. that is t... Jan 1 2011, 01:53 PM
detoxcowboy
Really depends how bad it is below that. that is ... Jan 1 2011, 01:56 PM detoxcowboy On further inspection of your pic, where is the en... Jan 1 2011, 01:54 PM C.Plavan
Here is a better close up picture.
The car wa... Jan 1 2011, 02:00 PM JRust the lower area circled i am not sure of. Looks lik... Jan 1 2011, 02:18 PM dr914@autoatlanta.com That damage is nothing! If the car is cheap e... Jan 1 2011, 02:03 PM J P Stein That alone is not a show stopper.....IF the of the... Jan 1 2011, 02:06 PM detoxcowboy DR. Auto Atlanta can provide all the replacement p... Jan 1 2011, 02:06 PM C.Plavan It has new floor pans, but notice the cut and weld... Jan 1 2011, 02:14 PM J P Stein Blow up your first pic and look at the edge of the... Jan 1 2011, 02:27 PM J P Stein Right below the clevis on the firewall Jan 1 2011, 02:32 PM C.Plavan
Right below the clevis on the firewall
I think... Jan 1 2011, 02:51 PM J P Stein There is a piece missing there, the doughnut brack... Jan 1 2011, 02:58 PM C.Plavan More pictures. Owner says he did a screwdriver te... Jan 1 2011, 04:55 PM C.Plavan more pictures
Jan 1 2011, 04:57 PM C.Plavan more
Jan 1 2011, 04:59 PM C.Plavan Rockers look a little different.
Jan 1 2011, 05:02 PM Spoke This car looks like an east coast rust bucket. The... Jan 1 2011, 05:08 PM kg6dxn Based on the last pictures... Buy a new tub and st... Jan 1 2011, 05:10 PM brant Chad,
good to see you on this board and looking ... Jan 1 2011, 05:19 PM Joe Sharp Post #21 :woohoo: :angry: It looks to me like tha... Jan 1 2011, 05:20 PM Racer Chris I would want to see pictures of the existing repai... Jan 1 2011, 07:28 PM SirAndy More than likely, those pictures would convince me... Jan 1 2011, 11:18 PM J P Stein :agree: Jan 1 2011, 07:35 PM MrHyde Those last pics look like what was done to my car ... Jan 1 2011, 10:59 PM hot_shoe914 Well, since nobody else asked, I will. Does that m... Jan 1 2011, 11:57 PM Racer Chris
Well, since nobody else asked, I will. Does that ... Jan 2 2011, 06:12 AM C.Plavan That was a 911 2.2L he had it in there to mock up ... Jan 2 2011, 10:01 AM detoxcowboy :blink: This thread started with a small hole.... ... Jan 2 2011, 10:01 AM J P Stein That's one nice 9eleben. :D
As for a parts ca... Jan 2 2011, 10:30 AM C.Plavan
That's one nice 9eleben. :D
As for a parts c... Jan 2 2011, 12:05 PM J P Stein
Thanks- I love that Blue monster.
Would it chan... Jan 2 2011, 12:44 PM kg6dxn Buy it for parts. cut the cage out carefully and r... Jan 2 2011, 12:18 PM C.Plavan Earlier, I was more concerned with that rust hole,... Jan 2 2011, 01:03 PM Racer Chris
Earlier, I was more concerned with that rust hole... Jan 2 2011, 03:38 PM jeeperjohn56 Hey Chad, Check with Craig(Boxstr) in the car want... Jan 2 2011, 06:11 PM realred914 that body should be run away from, too much rust t... Jan 3 2011, 01:41 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 11:19 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.