 Remove Engine, How High Do I Need to Lift the Car to Get Engine Out |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| badboybear |
 Feb 2 2011, 11:57 AM
Post
#1
|
|
Member  Group: Members Posts: 70 Joined: 27-January 11 From: Salem, OR Member No.: 12,632 Region Association: None  |
[size=3]How high do I need jack the car up to take the engine out from the bottom? Does anyone have a diagram for removing the engine....what bolts & where to remove, want to drop tranny & motor at once...hopefully.
Also where do I look or go to get a "repair kit" for the HELL HOLE. Told there is a metal replacment type piece? Thanks all, M&T914 |
   |
 
|
  |
Replies
| toon1 |
Feb 2 2011, 12:09 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,849 Joined: 29-October 05 From: tracy,ca Member No.: 5,022 |
I don't know the excact height but it's in the 18" range. Depending o the jack or dolly that you are going to use to set the engine on will determine the height.
most of the bolts and nuts will be 10-14 mm. with the exception of the main motor mount and the trans. mount bolts which are 17mmIIRC. The motor is not difficult to remove, just make sure everything is disconnected and it will drop right down. with NO experience at doing this, it's about a 2.5 hour job. For the seasoned "pro" 45min to an 1.5 hours alone. |
|
|
|
Posts in this topic
badboybear Remove Engine Feb 2 2011, 11:57 AM
Scarlet75 Go to914 info at thhe top and click on Tech articl... Feb 2 2011, 12:04 PM
SirAndy
Go to914 info at thhe top and click on Tech artic... Feb 2 2011, 10:43 PM tradisrad While I dont have an exact height to jack the car ... Feb 2 2011, 12:17 PM badboybear
While I dont have an exact height to jack the car... Feb 2 2011, 12:27 PM tradisrad
Nah, no blood required.
Check your CV bolts; the... Feb 2 2011, 12:44 PM silver74insocal
Nah, no blood required.
Check your CV bolts; th... Feb 2 2011, 10:03 PM stugray Oh.... AND drain the oil FIRST ;-)
I used to be a... Feb 2 2011, 01:30 PM badboybear
Oh.... AND drain the oil FIRST ;-)
I used to be ... Feb 2 2011, 02:16 PM Jerry75914 There is a good article on the PP site "engin... Feb 2 2011, 02:51 PM detoxcowboy 914 Engine Removal Made Easy
http://www.pelicanpar... Feb 2 2011, 02:52 PM badboybear
914 Engine Removal Made Easy
http://www.pelicanpa... Feb 2 2011, 05:39 PM jt914-6 Don't forget the tranny ground strap..... :hea... Feb 2 2011, 03:47 PM stugray Oh, and use zip ties or coat hangers to hold the a... Feb 2 2011, 04:22 PM Jeffs9146 The higher the better!! :blink: Feb 2 2011, 09:17 PM Drums66
The higher the better!! :blink:
.....Ge... Sep 2 2011, 12:12 PM rohar I took 4 1" 16gauge tubes and drilled some ho... Feb 2 2011, 10:43 PM JmuRiz Experts, I have a couple of questions:
What are s... Sep 2 2011, 11:47 AM jimkelly damn scary high for a V8 - slightly less for a 4.
... Sep 2 2011, 12:01 PM JawjaPorsche Do I see antifreeze on the driveway? Be sure to k... Sep 2 2011, 12:09 PM Dave_Darling The rear of the car needs to be about 2" high... Sep 2 2011, 07:11 PM Kirmizi Having done this recently, I'd suggest taking ... Sep 2 2011, 08:06 PM Vacca Rabite High.
I put my jackstands on 4x4 timbers. Make s... Sep 2 2011, 08:26 PM bigkensteele I swear by the "threaded rod" method. Y... Sep 2 2011, 08:26 PM larss
I swear by the "threaded rod" method. ... Sep 2 2011, 11:06 PM rhodyguy with carbs on a 4 if you remove the carbs as an as... Sep 3 2011, 08:23 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th July 2025 - 07:31 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.