 Converting to Carbs, What is a good setup for F Pump and Pressure |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| falconfp2001 |
 Mar 24 2011, 02:57 PM
Post
#1
|
|
Pancho Pantera  Group: Members Posts: 451 Joined: 5-December 10 From: Downey, CA Member No.: 12,456 Region Association: Southwest Region  |
I'm gonna setup dual carbs and would like to use the stock Fuel Pump but I'm trying to figure out how to setup the Pressure Regulators.
My idea is to keep my return line to the gas tank and just have two regulators. One before the carbs and another after. Anyone have a good suggestion? Thanks |
   |
 
|
  |
Replies
| jmill |
Mar 24 2011, 09:18 PM
Post
#2
|
|
Green Hornet Group: Members Posts: 2,449 Joined: 9-May 08 From: Racine, Wisconsin Member No.: 9,038 Region Association: Upper MidWest |
QUOTE(moparrob @ Mar 24 2011, 09:53 PM)  Very sweet setup. I like the billet pump. I'll have to keep this in mind when I get the 6 running. At 110 GPH it's overkill for a stockish 4 cylinder. |
|
|
|
Posts in this topic
falconfp2001 Converting to Carbs Mar 24 2011, 02:57 PM
jmill If I were you I'd save a ton of cash and get a... Mar 24 2011, 04:02 PM dirk9141973 :idea: Ok think this out little bit ? Sell the old... Mar 24 2011, 04:29 PM jjackson :agree: Ran CB pump for years on several motor com... Mar 24 2011, 05:04 PM jt914-6 As has been said....get a CB pump up front with a ... Mar 24 2011, 05:15 PM Cap'n Krusty We have a name for people who use the stock FI pum... Mar 24 2011, 06:10 PM
Elliot Cannon
We have a name for people who use the stock FI pu... Mar 24 2011, 09:00 PM moparrob I went with the Holley 125 low pressure pump and t... Mar 24 2011, 08:53 PM Elliot Cannon CB Performance rotary pump. "Works fine, las... Mar 24 2011, 08:58 PM NJ914Guy My shop is just wrapping up my 1973 2.0. Went wit... Mar 24 2011, 09:28 PM jmill Had a Facet on a dual carbed high reving 1914 cc V... Mar 24 2011, 09:45 PM falconfp2001 Think I like this Regulator
I also like the Holle... Mar 25 2011, 02:10 AM NJ914Guy Yep, heard good and bad about the Facet and CB Rot... Mar 25 2011, 05:33 AM Ericv1
Yep, heard good and bad about the Facet and CB Ro... Mar 25 2011, 04:11 PM jimkelly would 30 gph be ok for my V8 ?? Mar 25 2011, 05:47 AM Root_Werks
would 30 gph be ok for my V8 ??
Jim, hopefully ... Mar 25 2011, 07:06 AM jimkelly ok - i should have said - i have this friend who p... Mar 25 2011, 01:17 PM McMark I prefer to go with a higher end pump and a qualit... Mar 25 2011, 03:58 PM nathansnathan From my experience with rotary pumps, they say the... Mar 25 2011, 04:12 PM jmill
would 30 gph be ok for my V8 ??
Be careful when... Mar 25 2011, 05:21 PM markb I had a facet on my carbed motor. Hated it. Noisy,... Mar 25 2011, 09:44 PM NJ914Guy Had her out today again for about a 40min run. Th... Mar 25 2011, 09:45 PM jimkelly sounds good - but i know i am gonna get me a good ... Mar 26 2011, 06:33 AM falconfp2001 what kind of distributor are you running? Mar 26 2011, 02:11 PM NJ914Guy I am running the old Bosch 009 with points elimina... Mar 26 2011, 10:17 PM Steve73 What about this for a fuel Pump?
http://www.tenn... Aug 7 2011, 10:40 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 09:35 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.