 Pressing in 100mm wheel studs, How to keep them straight? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Phoenix-MN |
 Jun 8 2011, 07:52 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 927 Joined: 23-January 04 From: ST. Bonifacius,MN Member No.: 1,590  |
(IMG:style_emoticons/default/confused24.gif) So, I'm installing 100mm wheel studs on my front 911 hubs to use with spacers. Stock ones press out easily and I start to press in the 100mm ones. After I get 3 pressed in the spacer still slides on and fits. After installing the 4th it starts to bind just a bit. After pressing in the 5th stud, the spacer will no longer slide on . They don't press in exactly perpendicular to the hub face and the spacer will not slide over the studs now. For those who have actually done this what's the trick in getting these pressed in straight?
Thanks Paul |
   |
 
|
  |
Replies
| SirAndy |
Jun 8 2011, 08:07 PM
Post
#2
|
|
Resident German Group: Admin Posts: 41,669 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California |
QUOTE(Phoenix-MN @ Jun 8 2011, 06:52 PM)  For those who have actually done this what's the trick in getting these pressed in straight? They will straighten out the first time you torque them down. If you can't get the spacer on right now, put it over one stud at the time and use a open end steel lug-nut to torque each one down. That will seat the stud correctly and they should work fine after that. The holes, backside of the hub around the holes and and the lower part of the stud have to be perfectly clean! Any dirt will prevent the stud from seating correctly ... (IMG:style_emoticons/default/smash.gif) |
|
|
|
| Randal |
Jun 8 2011, 08:11 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 4,446 Joined: 29-May 03 From: Los Altos, CA Member No.: 750 |
QUOTE(SirAndy @ Jun 8 2011, 07:07 PM) QUOTE(Phoenix-MN @ Jun 8 2011, 06:52 PM) For those who have actually done this what's the trick in getting these pressed in straight? They will straighten out the first time you torque them down. If you can't get the spacer on right now, put it over one stud at the time and use a open end steel lug-nut to torque each one down. That will seat the stud correctly and they should work fine after that. The holes, backside of the hub around the holes and and the lower part of the stud have to be perfectly clean! Any dirt will prevent the stud from seating correctly ... (IMG:style_emoticons/default/smash.gif) I second what Andy said. I used a big torque gun on mine and lots of washers to get them to seat. |
|
|
|
Posts in this topic
Phoenix-MN Pressing in 100mm wheel studs Jun 8 2011, 07:52 PM
rick 918-S I didn't have the luxury of having a 911 front... Jun 8 2011, 08:09 PM Phoenix-MN
For those who have actually done this what's... Jun 9 2011, 09:19 AM
jaxdream I made a fixture to use on my press ( I am fortuna... Jun 9 2011, 09:39 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 05:37 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.