 Seized engine sheet metal screws, Better ask before I break out the drill |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| MrHyde |
 Sep 27 2011, 04:24 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 525 Joined: 13-October 10 From: Ontario, Canada Member No.: 12,268 Region Association: None  |
So.... in order to get a bit more room in the garage after the move, so I can start welding on the body i figured I'd work on getting the engine up on a stand an off to the side for a little bit... I have the tranny off and wires/FI stripped off and boxed up and have been taking the sheet metal screws off.. I have 4 that are totally seized on... 3 of them at the intake ports and one on the fan shroud.. I've soaked them with pb blaster and all i've managed to do it mangle the slot in the screw a bit..
I'm inclined to just drill out the screws and tap them afterwards... Before I do this, does anyone have any time tested suggestions to get these buggers off?? If not, does anyone know off hand what size the tap / drill I'll need to use ? Thanks ! Mike |
   |
 
|
  |
Replies
| GeorgeRud |
Sep 28 2011, 11:13 AM
Post
#2
|
|
Advanced Member Group: Members Posts: 3,725 Joined: 27-July 05 From: Chicagoland Member No.: 4,482 Region Association: Upper MidWest |
I've also had better luck using Kroil as a penetranting liquid. Give it time to work overnight, then heat and patience are your friends.
Anti seize when reassembling is also a nice touch to make the next repair easier. |
|
|
|
Posts in this topic
MrHyde Seized engine sheet metal screws Sep 27 2011, 04:24 PM
Vacca Rabite if you have an impact driver you could try tapping... Sep 27 2011, 04:29 PM nathansnathan I would try grabbing the head with vise grips befo... Sep 27 2011, 04:32 PM Jeffs9146 I had the same problem and after 3 days of PB I he... Sep 27 2011, 04:33 PM tradisrad A big screw driver that does not slip/strip out al... Sep 27 2011, 04:37 PM Eric_Shea MAPP Torch. Sep 27 2011, 04:42 PM MrHyde I just sprayed them (again ) with PB Blaster.. I... Sep 27 2011, 04:51 PM wingnut86 I love PB, it runs through my veins nowadays :head... Sep 27 2011, 05:54 PM bigkensteele I just went through this a couple of weeks ago. I... Sep 27 2011, 05:55 PM r_towle Impact screw driver was invented to take out slott... Sep 27 2011, 06:11 PM Dave_Darling I found that having the actual correct size of scr... Sep 27 2011, 09:56 PM
majkos
I found that having the actual correct size of sc... Sep 27 2011, 10:10 PM vsg914 I'm another for the impact. If you dont have o... Sep 28 2011, 04:53 AM Gint Last time I removed tin, and impact screwdriver go... Sep 28 2011, 05:45 AM larss Had the same problem some weeks ago, a heat gun wo... Sep 28 2011, 07:41 AM sean_v8_914 most of the advice above is solid. patience is the... Sep 28 2011, 07:53 AM dlestep ...I have a special tool just for that. A B I G f... Sep 28 2011, 08:33 AM mikea100 I had the same problem. It took 2 people, my buddy... Sep 28 2011, 08:50 AM sean_v8_914 teamwork! love it Sep 28 2011, 09:04 AM MrHyde Final verdict... Maap torch, pb blaster and impact... Oct 7 2011, 01:17 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 13th May 2025 - 08:24 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.