 High Mileage EA motor teardown, 330,000 miles + |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| mgphoto |
 Sep 28 2011, 05:56 PM
Post
#1
|
|
"If there is a mistake it will find me"  Group: Members Posts: 1,375 Joined: 1-April 09 From: Los Angeles, CA Member No.: 10,225 Region Association: Southern California  |
The time has come to rebuild the original EA motor in my '72.
I am most of the way though teardown, I will add some photos of the worn parts in a later post. I am trying to figure out the size of the tool to use to remove this fastener, the cover for the second oil pressure relief piston and spring.  Factory service manual has it as M14 internal head socket. I searched for it but all I could find is the AST Tool # S 54 X-14 at the link listed below http://www.asttool.com/detail_page.php?too...r=S%2054%20X-14 Does anyone know if this is the correct tool? Thanks for looking, Mike |
   |
 
|
  |
Replies
| VaccaRabite |
Oct 12 2011, 06:50 PM
Post
#2
|
|
En Garde! Group: Admin Posts: 13,729 Joined: 15-December 03 From: Dallastown, PA Member No.: 1,435 Region Association: MidAtlantic Region 
|
That is an intake valve guide dropping into the head. Eventually it would have let to valve/piston contact.
Zach |
|
|
|
| mgphoto |
Oct 13 2011, 06:10 PM
Post
#3
|
|
"If there is a mistake it will find me" Group: Members Posts: 1,375 Joined: 1-April 09 From: Los Angeles, CA Member No.: 10,225 Region Association: Southern California |
QUOTE(Vacca Rabite @ Oct 12 2011, 05:50 PM)  That is an intake valve guide dropping into the head. Eventually it would have let to valve/piston contact. Zach Whoo, just in time!! |
|
|
|
Posts in this topic
mgphoto High Mileage EA motor teardown Sep 28 2011, 05:56 PM
vsg914 If I recall correctly, its the same tool you use f... Sep 28 2011, 06:06 PM mgphoto Hey vsg914, just checked and the axle tool is much... Sep 28 2011, 06:15 PM RON S. When I needed an internal 12pt tool for my CV... Sep 28 2011, 06:20 PM '73-914kid 3/8 inch drive socket extension worked for me....i... Sep 28 2011, 06:20 PM vsg914 You are correct. Its called a tripple square, amon... Sep 28 2011, 06:24 PM
mgphoto
You are correct. Its called a tripple square, amo... Sep 28 2011, 09:36 PM rick 918-S Wow! 330K? Very cool! :popcorn: Sep 28 2011, 09:50 PM 76-914
Wow! 330K? Very cool! :popcorn:
That... Sep 29 2011, 04:48 PM McMark Yup, never used anything but a 3/8" drive ext... Sep 28 2011, 11:17 PM mgphoto I ran into a small snag, trying to remove the head... Sep 29 2011, 12:25 PM Jake Raby To remove that triple square fastener give it two ... Sep 29 2011, 05:12 PM mgphoto I bought the car in the '80's, 96k on the ... Sep 30 2011, 06:46 PM Valy
Pulled the motor at 337,xxx broke 2 angle drives ... Sep 30 2011, 07:12 PM 76-914
[quote name='mgphoto' post='1547261... Oct 1 2011, 11:48 AM mgphoto I took the case over to Engine Machine Services, t... Oct 5 2011, 01:27 PM r_towle Dont glass bead it, you wont see it after you buil... Oct 5 2011, 01:35 PM mgphoto
Dont glass bead it, you wont see it after you bui... Oct 5 2011, 04:16 PM mgphoto OK dismantled the heads, there is one odd item, on... Oct 12 2011, 06:22 PM mgphoto OK got the case back after cleaning and tapping th... Oct 13 2011, 06:13 PM HAM Inc That head with the dropping intake valve guide has... Oct 13 2011, 07:03 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 03:12 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.