 Need hardware electroplated |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Harpo |
 Nov 8 2011, 07:58 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,304 Joined: 21-August 11 From: Motor City aka Detroit Member No.: 13,469 Region Association: None  |
I have some components that I would like to get cleaned up and replated in yellow zinc. Is there someone that makes regular runs to the plater?
Hood striker & latch, trunk striker & latch, engine compartment striker & latch, rear wheel hub, etc. Thanks David |
   |
 
|
  |
Replies
| Series9 |
Nov 9 2011, 08:47 AM
Post
#2
|
|
Lesbians taste like chicken. Group: Members Posts: 5,446 Joined: 22-August 04 From: DeLand, FL Member No.: 2,602 Region Association: South East States |
I can have it done for you.
Yellow zinc Clear zinc or Cadmium |
|
|
|
| Harpo |
Nov 9 2011, 05:37 PM
Post
#3
|
|
Senior Member Group: Members Posts: 1,304 Joined: 21-August 11 From: Motor City aka Detroit Member No.: 13,469 Region Association: None |
Because yellow zinc & cadmium are so close in appearance I would say that I want which ever is cheaper. With zinc I know that you need to be in the oven @ 400 with in an hour to bake off the hydrogen. I'm just concerned about the springs. Or should I just remove them?
Thanks David QUOTE(Series9 @ Nov 9 2011, 06:47 AM)  I can have it done for you. Yellow zinc Clear zinc or Cadmium |
|
|
|
| Series9 |
Nov 14 2011, 06:25 PM
Post
#4
|
|
Lesbians taste like chicken. Group: Members Posts: 5,446 Joined: 22-August 04 From: DeLand, FL Member No.: 2,602 Region Association: South East States |
QUOTE(Harpo @ Nov 9 2011, 06:37 PM) Because yellow zinc & cadmium are so close in appearance I would say that I want which ever is cheaper. With zinc I know that you need to be in the oven @ 400 with in an hour to bake off the hydrogen. I'm just concerned about the springs. Or should I just remove them? Thanks David QUOTE(Series9 @ Nov 9 2011, 06:47 AM) I can have it done for you. Yellow zinc Clear zinc or Cadmium Actually, the best response is "Zinc is more environmentally friendly". There isn't much difference in cost and Cad is usually more. I do springs all the time and they're done correctly. |
|
|
|
Posts in this topic
Harpo Need hardware electroplated Nov 8 2011, 07:58 PM
Tom_T I think that Eric at PMB (member vendor on here wh... Nov 8 2011, 08:28 PM McMark I send stuff to Sacramento all the time for platin... Nov 8 2011, 10:59 PM jeeperjohn56 Talk to Bruce (bdstone914) he might have some alre... Nov 9 2011, 07:23 AM
A&PGirl I make semi-regular runs to the only plater. :(
... Nov 9 2011, 02:00 PM PanelBilly Remove the springs and send extra nuts and bolts. ... Nov 14 2011, 05:33 PM
Eric_Shea I go once or twice a week here.
Much easier to ... Nov 14 2011, 09:58 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 07:39 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.