 bearing inspection, how do these look? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Cool914 |
 Nov 21 2011, 11:14 AM
Post
#1
|
|
Member  Group: Members Posts: 98 Joined: 25-January 11 From: Ontario Member No.: 12,627 Region Association: Canada  |
Taking apart a fresh rebuilt 2.0 and i noticed the heads qere on wrong side. The one with the head temp sensor spot was on 1,2cylinder side. possible reasons, problems?
|
   |
 
|
  |
Replies
| Mark Henry |
Nov 26 2011, 12:05 AM
Post
#2
|
|
that's what I do! Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada |
Looks like bus pistons. Heads don't look too bad
I can help with what you may need, PM me. QUOTE Is that seam on the inside of the intake part of the casting, seems to be in all the the intakes? Normal casting marks. |
|
|
|
Posts in this topic
Cool914 bearing inspection Nov 21 2011, 11:14 AM
McMark Inattentive rebuilder. I did that on one of my fi... Nov 21 2011, 11:16 AM
Cool914
Inattentive rebuilder. I did that on one of my f... Nov 21 2011, 12:09 PM Cool914 So I started to take my "rebuilt" motor ... Nov 25 2011, 11:20 PM Cool914 Last one of intake and some of cylinders. They loo... Nov 25 2011, 11:28 PM bam914 I would have the valves replaced that one with all... Nov 26 2011, 09:30 AM jmill
I would have the valves replaced that one with al... Nov 26 2011, 09:42 AM jcd914
looks like one intake valve and guide have been r... Nov 26 2011, 11:06 AM Jake Raby Reusing valves is Russian Roulette.. Especially th... Nov 26 2011, 02:56 PM MrHyde
Looks like bus pistons. Heads don't look too ... Nov 26 2011, 03:50 PM Cool914 Thanks for the advice everyone. They will be getti... Nov 26 2011, 07:03 PM Dave_Darling Very common; that's the cover over the bottom ... Nov 26 2011, 11:33 PM sean_v8_914 post #12 is a tribute to Sir Andy Nov 27 2011, 09:33 AM Cool914 Do I need a new clutch disc?
Seriously though, do ... Nov 28 2011, 06:02 PM mrholland2
Do I need a new clutch disc?
Seriously though, do... Jan 2 2012, 10:33 PM a914dude Down to the rivits? Yes. Nov 28 2011, 06:16 PM Mark Henry When you come down to see me bring it with you, I ... Nov 28 2011, 06:47 PM Cool914 So I finally had time to finish the tear down. Did... Jan 2 2012, 08:49 PM Cool914 the rest
Jan 2 2012, 08:56 PM Cool914
sorry, here is a good one of the impression of t... Jan 2 2012, 09:00 PM SirAndy This is hurting my eyes! :poke:
Find the ma... Jan 2 2012, 09:03 PM Cool914
This is hurting my eyes! :poke:
Find the m... Jan 2 2012, 09:08 PM malcolm2 All those bearings look brand new compared to mine... Jan 2 2012, 09:25 PM Cool914
All those bearings look brand new compared to min... Jan 2 2012, 09:28 PM messix that whole mess is ugly, rebuilt when?
and you ar... Jan 2 2012, 10:53 PM Cool914 I don't have any history on the engine, was to... Jan 2 2012, 11:14 PM malcolm2
I don't have any history on the engine, was t... Jan 3 2012, 10:54 AM malcolm2
Anyone have any comments on the hammering of the... Jan 3 2012, 11:04 AM Cool914
Anyone have any comments on the hammering of th... Jan 3 2012, 09:38 PM 76-914 Andy is just jazzing you about the photo's. A ... Jan 3 2012, 09:32 AM Cool914
Andy is just jazzing you about the photo's. A... Jan 3 2012, 09:49 AM underthetire This one looks toast for sure.. Jan 3 2012, 10:20 AM Cool914
This one looks toast for sure..
That was from my... Jan 3 2012, 10:29 AM Valy You need new bearings. All of them for sure.
You m... Jan 3 2012, 04:47 PM Jeff Hail The more I look the more I see.
May not be anyt... Jan 3 2012, 08:22 PM Cool914
The more I look the more I see.
May not be any... Jan 3 2012, 09:40 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st August 2025 - 06:36 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.