 Bosch Distributor VS MSD Ignition, Rotor Bosch Dist. melted when ignited w/ SS Blaster Coil and 6AL |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Ghianto66 |
 Nov 27 2011, 11:33 PM
Post
#1
|
|
Newbie  Group: Members Posts: 5 Joined: 11-November 10 From: Jakarta, Indonesia Member No.: 12,372 Region Association: Indonesia  |
Is thre anyone have experiance w/ melted distributor rotor? I have 2.0 motor with MSD 6AL and SS blaster coil, I drive for 100miles but suddenly engine stop, I check for ignition but no FIRE. I check for distributor and it shown melted rotor. I change w/ new rotor but when 100miles it happen again. Distributor its self is original BOSCH. Anyone know which rotor that fit w/ bosch and can hold MSD fire?
Attached thumbnail(s) 
|
   |
 
|
  |
Replies
| ArtechnikA |
Nov 28 2011, 04:34 AM
Post
#2
|
|
rich herzog Group: Members Posts: 7,390 Joined: 4-April 03 From: Salted Roads, PA Member No.: 513 Region Association: None |
QUOTE(Ghianto66 @ Nov 28 2011, 12:33 AM)  Is thre anyone have experiance w/ melted distributor rotor?...Distributor its self is original BOSCH. Anyone know which rotor that fit w/ bosch and can hold MSD fire? I had one explode. You mentioned the distributor is Bosch - is the ROTOR also Bosch? My exploding rotor was a generic (Beck-Arnley?) replacement - all I could get locally. Replaced it with a real Bosch rotor and never had that problem again. |
|
|
|
| Ghianto66 |
Nov 28 2011, 05:16 AM
Post
#3
|
|
Newbie Group: Members Posts: 5 Joined: 11-November 10 From: Jakarta, Indonesia Member No.: 12,372 Region Association: Indonesia |
Yes, mine was BOSCH distributor and rotor, the rotor it self is NOS where noted W-
Germany. Ground connection is good, I have add more cable to make the connection more adequate. I'll try to drive this car about 100 again tomorrow, if this still happend again I let you guys know. QUOTE(ArtechnikA @ Nov 28 2011, 05:34 PM) QUOTE(Ghianto66 @ Nov 28 2011, 12:33 AM) Is thre anyone have experiance w/ melted distributor rotor?...Distributor its self is original BOSCH. Anyone know which rotor that fit w/ bosch and can hold MSD fire? I had one explode. You mentioned the distributor is Bosch - is the ROTOR also Bosch? My exploding rotor was a generic (Beck-Arnley?) replacement - all I could get locally. Replaced it with a real Bosch rotor and never had that problem again. |
|
|
|
Posts in this topic
Ghianto66 Bosch Distributor VS MSD Ignition Nov 27 2011, 11:33 PM
kg6dxn Never seen that happen before. I would assume bad ... Nov 27 2011, 11:38 PM Krieger I have a MSD 6A Box and Blaster 2 coil with close ... Nov 27 2011, 11:42 PM kconway There are numerous threads on this issue on Pelica... Nov 28 2011, 12:12 AM Ghianto66 I have check for spark wire and its shown 0 ohm, s... Nov 28 2011, 12:25 AM
sean_v8_914 rotor to cap engagement depth Nov 28 2011, 08:11 AM Gint I remember a very old thread about someone modifyi... Nov 28 2011, 09:23 AM Gint Check out this thread:
http://www.914world.com/bb... Nov 28 2011, 09:27 AM Cap'n Krusty I don't have a fix, but I've seen the prob... Nov 28 2011, 09:36 AM wingnut86 Also keep in mind that Jakarta is always hot and h... Nov 28 2011, 01:15 PM Cap'n Krusty The big question here is why do you think you need... Nov 28 2011, 01:42 PM
Marty Yeoman I run a MSD 6AL with a Bosch Blue coil, stock Bosc... Nov 28 2011, 02:38 PM Ghianto66 back from my journey, around 300 miles outside fro... Dec 2 2011, 12:23 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th June 2024 - 06:08 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.