 KB pistons, Anyone seen these? UPDATE! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Black22 |
 Dec 5 2011, 10:42 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 886 Joined: 1-November 07 From: Creswell, OR Member No.: 8,290 Region Association: Pacific Northwest  |
I read a lot about the KB Hypereutectic pistons but, I've not really heard about the Silv-o-lites. From what I researched these are hypereutectic pistons as well but, I can't seem to find the part number on the box anywhere online.
Anyone know if these definitely work as the 96mm "Big Bore" kit for a 1.8L? That's what the seller claimed and I got a screamin' deal for these. Seriously, I paid less than a hundred bucks for this set! Anyone?     |
   |
 
|
  |
Replies
| Black22 |
Dec 6 2011, 12:51 PM
Post
#2
|
|
Senior Member Group: Members Posts: 886 Joined: 1-November 07 From: Creswell, OR Member No.: 8,290 Region Association: Pacific Northwest |
QUOTE(Mark Henry @ Dec 6 2011, 10:09 AM)  Found one 1.8, 1.178" again from the top of the pin to the top of the piston. Thank you. I'll have to check the height tomorrow as I'm at work now and the pistons are in storage. Thanks again for the important info! |
|
|
|
| reharvey |
Dec 6 2011, 01:53 PM
Post
#3
|
|
Senior Member Group: Members Posts: 573 Joined: 16-July 08 From: N. E. Ohio Member No.: 9,308 Region Association: North East States |
QUOTE(Black22 @ Dec 6 2011, 01:51 PM) QUOTE(Mark Henry @ Dec 6 2011, 10:09 AM) Found one 1.8, 1.178" again from the top of the pin to the top of the piston. Thank you. I'll have to check the height tomorrow as I'm at work now and the pistons are in storage. Thanks again for the important info! Those look like NOS pistons from a decade ago ( or longer ) . If you lay a 1.7 piston next to it I'm sure you'll find that it's a perfect match for the wrist pin location. Hastings has the rings for those and cylinders are available. |
|
|
|
Posts in this topic
Black22 KB pistons Dec 5 2011, 10:42 PM
McMark That wrist pin is low. I just installed a set of ... Dec 5 2011, 10:57 PM
Mark Henry
That wrist pin is low. I just installed a set of... Dec 5 2011, 11:35 PM 7275914911 If they end up being for a 2.0 and not a 1.8then..... Dec 6 2011, 06:16 AM Black22
That wrist pin is [i]low. I just installed a set... Dec 6 2011, 10:50 AM Mark Henry Unfortunately I don't have a 1.8 piston kickin... Dec 6 2011, 11:23 AM Mark Henry Found one
1.8, 1.178" again from the top ... Dec 6 2011, 12:09 PM McMark I can't measure the ones I used since they... Dec 6 2011, 12:49 PM Black22
Yeah, that's what the seller said. He had th... Dec 6 2011, 02:43 PM Black22 Well after a few emails to KB and a call to Europe... Dec 8 2011, 01:08 PM Mark Henry They still look high to me, did you actually measu... Dec 8 2011, 03:21 PM Black22
They still look high to me, did you actually meas... Dec 14 2011, 12:43 PM Mark Henry Sounds close for a 1.7/1.8, good score.
Mr. Henry... Dec 14 2011, 01:06 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 15th April 2026 - 01:12 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.