 need to do a clutch today, can I do it w/out removing the trans? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| ottox914 |
 May 25 2012, 06:27 AM
Post
#1
|
|
The glory that once was.  Group: Members Posts: 1,302 Joined: 15-December 03 From: Mahtomedi, MN Member No.: 1,438 Region Association: Upper MidWest   |
Been a bit since the last time I did a clutch IN a car. I seem to recall hearing of doing one w/out taking the trans out. I'd rather not have to do that, as removing the exhaust, turbo bits, and trans adds a lot more work. Ant thoughts or hints/tips? Its just me in the garage today, so hopefully I can get this done for the weekend.
|
   |
 
|
  |
Replies
| Cap'n Krusty |
May 25 2012, 08:08 AM
Post
#2
|
|
Cap'n Krusty Group: Members Posts: 10,794 Joined: 24-June 04 From: Santa Maria, CA Member No.: 2,246 Region Association: Central California |
It CAN be done without removing the tranny from the car. I've seen it done by pulling it back and letting it hang by the axles, laying on the HEs. The guy doing it believed it was faster, but I'm not so sure. Still, under an hour IS pretty good time.
The Cap'n |
|
|
|
Posts in this topic
ottox914 need to do a clutch today May 25 2012, 06:27 AM
r_towle nope, it needs to come out.
rich May 25 2012, 06:38 AM URY914 You could leave the trany in but it would be the f... May 25 2012, 06:40 AM Dr Evil Wow, it would be the first time I have heard of it... May 25 2012, 06:41 AM Dr Evil Actually, ya you can leave the tranny in, but you ... May 25 2012, 06:41 AM r_towle I suppose if you have some training in magic it mi... May 25 2012, 06:43 AM
bembry
If you still have the underbody heat shield in p... Jun 4 2012, 04:32 PM Luke M Every clutch job that I've done in a 914 I had... May 25 2012, 06:44 AM dakotaewing Wouldn't it be faster to drop the entire drive... May 25 2012, 08:54 AM rjames
Please don't let anything rest on the heat e... May 25 2012, 10:24 AM pt_700 although it's been awhile for me too, i agree ... May 25 2012, 10:33 AM ottox914 I've had an engine and trans out more times th... May 25 2012, 03:12 PM Dr Evil Dave, reply sent. Lets do this! :evilgrin: May 25 2012, 03:44 PM ottox914 Just gave in and pulled the trans after taking som... May 29 2012, 02:47 PM Cupomeat THat is VERY unusual.
Perhaps one side of the dia... May 29 2012, 02:55 PM Dr Evil Any of those disks should be fine. The 4 spring di... May 29 2012, 03:00 PM Valy How is your flywheel?
Looks like the throwout bear... May 29 2012, 05:27 PM ottox914 Hows THIS for customer service...
On Jun 4, 2012... Jun 4 2012, 08:46 AM ape914
Been a bit since the last time I did a clutch IN ... Jun 4 2012, 11:57 AM ottox914
Been a bit since the last time I did a clutch IN... Jun 4 2012, 05:07 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 4th November 2025 - 04:21 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.