 Clewett Engineering - Crank fire |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Harpo |
 Dec 8 2012, 07:33 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,304 Joined: 21-August 11 From: Motor City aka Detroit Member No.: 13,469 Region Association: None  |
Good evening
Is anyone using the Clewett Engineering crank fire set up? http://www.clewett.com/index.php?main_page...products_id=291 Thanks David |
   |
 
|
  |
Replies
| edwin |
Dec 8 2012, 11:44 PM
Post
#2
|
|
Member Group: Members Posts: 321 Joined: 20-May 09 From: Australia Member No.: 10,384 Region Association: Australia and New Zealand |
Pretty sure joe at series 9 used one on a build
Personally it looks over engineered because they didn't think it through Hangs a shaft off the front of the fan and has the trigger wheel in front of the housing Mac marks setup is much much nicer and I used a different solution on mine that ill try get some photos of when I get home tonight My 2c Edwin |
|
|
|
| ellisor3 |
Dec 8 2012, 11:57 PM
Post
#3
|
|
HPWhore Group: Members Posts: 811 Joined: 23-October 08 From: Fleming Island, Florida Member No.: 9,683 Region Association: South East States  |
QUOTE(edwin @ Dec 9 2012, 12:44 AM)  Pretty sure joe at series 9 used one on a build Personally it looks over engineered because they didn't think it through Hangs a shaft off the front of the fan and has the trigger wheel in front of the housing Mac marks setup is much much nicer and I used a different solution on mine that ill try get some photos of when I get home tonight My 2c Edwin I have Electromotive on my 6, and yes Joe did do the install. You can see it in my signature. It is expensive, but once it is set up it is bullet proof. It is laptop programable. |
|
|
|
Posts in this topic
Harpo Clewett Engineering - Crank fire Dec 8 2012, 07:33 PM
kg6dxn Spendy... I think there are cheaper solutions... A... Dec 8 2012, 08:00 PM Mark Henry Not the same Mark but....
I'm assuming this i... Dec 8 2012, 08:33 PM Mark Henry I should add running megasquirt crankfire gives yo... Dec 8 2012, 08:43 PM McMark I've been looking into a trigger setup for six... Dec 8 2012, 10:35 PM
Mark Henry
I've been looking into a trigger setup for si... Dec 9 2012, 07:42 AM 396
Good evening
Is anyone using the Clewett Enginee... Dec 8 2012, 11:55 PM edwin The kit in the link is for a 4cyl
I like their com... Dec 9 2012, 12:38 AM Harpo I agree that the fan mounted pick up is expensive ... Dec 9 2012, 06:15 AM carr914 I have used it in the Past on 2 Cars in Twin-Plug ... Dec 9 2012, 08:00 AM Harpo My application is a 4, I was under the impression ... Dec 9 2012, 08:16 AM Mark Henry
My application is a 4, I was under the impression... Dec 9 2012, 09:25 AM GeorgeRud I've had the Clewitt setup on my conversion -6... Dec 9 2012, 09:30 AM Mark Henry BTW the reason the /6 carb guys run a Clewett or m... Dec 9 2012, 09:34 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 03:52 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.