 New Work Bench, Top Suggestions? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jfort |
 Dec 20 2012, 11:47 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,185 Joined: 5-May 03 From: Findlay, OH Member No.: 652 Region Association: Upper MidWest 
 |
I am going to make a new work bench this winter. Maybe 30" by 16'. 4 by 4's. drawers and a shelf across the bottom. A vise. I am just your typical once-in-while car project and home project type guy.
Don't know what to do for the top. I see places make butcher block. I put formica-type stuff on top of 3/4" plywood one time. I've though about a sheet of metal, but something tells me not to do that. Suggestions? Any other suggestion about a work bench would be appreciated, too. For example, I've thought about getting 2 or 3 half-sized metal shop drawer thinks, bolting them together and putting a work bench top on that. What do you think? |
   |
 
|
  |
Replies
| yp914 |
Dec 20 2012, 04:38 PM
Post
#2
|
|
typ914 Group: Members Posts: 6 Joined: 27-October 12 From: Ga Member No.: 15,086 Region Association: South East States |
I agree a solid core wood door is the best table top. It will be flat and smooth. Strong enough to bolt a vice or to hammer metal on. Find a local commercial door company or installer and they might give you a damaged one or an old one. I have several doors and if you were local you could have one of these. When I had my shop I took a fire rated door and bolted a 1/8' steel plate to it and used it for a welding table!! Worked great!
|
|
|
|
Posts in this topic
jfort New Work Bench Dec 20 2012, 11:47 AM
URY914 If you want a wood top, try a building supply that... Dec 20 2012, 11:52 AM
Andyrew
If you want a wood top, try a building supply tha... Jan 9 2013, 10:25 PM two-strokejohn I like metal tops on my workbenches, because they ... Dec 20 2012, 11:57 AM jfort what gauge stainless? how did you hold it down? Dec 20 2012, 12:04 PM mwyatt I used a sheet of stainless over MDF. Don't r... Dec 20 2012, 12:33 PM two-strokejohn
what gauge stainless? how did you hold it down?
... Dec 20 2012, 03:07 PM kg6dxn I have a galvanized steel skin on one of mine. I f... Dec 20 2012, 12:40 PM DBCooper It depends a lot on what you want to use it for. ... Dec 20 2012, 12:44 PM URY914
Gint's solid core door suggestion is a good... Dec 20 2012, 01:24 PM DBCooper
Gint's solid core door suggestion is a goo... Dec 20 2012, 01:55 PM Gint Gint's solid core door suggestion is a good ... Dec 20 2012, 11:16 PM underthetire Check your local C/L first. Sometimes it's rea... Dec 20 2012, 12:44 PM abnrdo I have this one from Sears.
8 Ft Butcher Block B... Dec 20 2012, 01:10 PM Vacca Rabite Plywood.
I have made bunches of work benches and t... Dec 20 2012, 01:12 PM 7TPorsh You can but stainless steel flashing for roofs in ... Dec 20 2012, 01:13 PM URY914 I also have a bench top made from a hollow metal d... Dec 20 2012, 01:26 PM stugray I was going to sugget the hollow metal door also -... Dec 20 2012, 01:36 PM 7TPorsh
I was going to sugget the hollow metal door also ... Dec 20 2012, 01:38 PM dpires914
I was going to sugget the hollow metal door also ... Dec 20 2012, 07:27 PM Dasnowman
I was going to sugget the hollow metal door also ... Dec 21 2012, 01:00 AM Elliot Cannon I laminated two 3/4 inch sheets of plywood. Rout... Dec 20 2012, 01:44 PM OU8AVW these look cool
http://www.creativeshelters.com/2... Dec 20 2012, 01:53 PM Mark Henry My main bench is 3 heavy industrial steel doors, I... Dec 20 2012, 03:18 PM Travis Neff I did mine with 3/4 plywood and covered in in 20G ... Dec 20 2012, 03:27 PM Jon H. I picked up used 5'x7' x 1/4 plate steel t... Dec 20 2012, 04:25 PM scotty b If you want to do a little elbow work, go to a lo... Dec 20 2012, 04:38 PM MDG
If you want to do a little elbow work, go to a l... Dec 20 2012, 07:20 PM scotty b
If you want to do a little elbow work, go to a ... Dec 20 2012, 08:00 PM MDG
[quote name='MDG' post='1787541' date='Dec 20 201... Dec 21 2012, 12:11 PM Scott S I used plywood, and then covered it with the peel ... Dec 20 2012, 05:19 PM zonedoubt Salvaged kitchen laminate countertop. Mine has sto... Dec 20 2012, 05:48 PM strawman
Salvaged kitchen laminate countertop. Mine has st... Dec 20 2012, 06:57 PM Tom Here is a pic of my work area. Not as large as I w... Dec 20 2012, 07:19 PM URY914 Here is a shot off my vise mounted on my hollow me... Dec 20 2012, 07:25 PM URY914 And my grinder mounted my solid core door OAK ....... Dec 20 2012, 07:26 PM URY914 Drill press is on a peice of plastic laminate coun... Dec 20 2012, 07:28 PM URY914 Working as a project manager for a construction co... Dec 20 2012, 07:30 PM dpires914
I am going to make a new work bench this winter. ... Dec 20 2012, 07:43 PM bigkensteele http://www.harborfreight.com/60-inch-workbench-934... Dec 20 2012, 08:07 PM oldschool Found this old kitchen table on the side of a road... Dec 20 2012, 08:55 PM euro911 This is a freebie I picked up from one of Joe Shar... Dec 20 2012, 09:04 PM cwpeden I covered mine with cheap laminate flooring from h... Dec 21 2012, 01:17 AM dian i did exactly the same.
besides i poured this one... Dec 21 2012, 10:17 AM rnellums I love this thread Dec 21 2012, 10:31 AM balljoint I am with scotty on the freebies. I found some gr... Dec 21 2012, 10:48 AM DBCooper
I am with scotty on the freebies. I found some g... Dec 21 2012, 11:22 AM MDG
Let's see, where are you from again? Good, ... Dec 21 2012, 12:13 PM Mark Henry
I am with scotty on the freebies. I found some g... Dec 21 2012, 05:40 PM struckn Here's a PORTABLE HEAVY TABLE WORK BENCH 4... Dec 21 2012, 10:56 AM rwilner
Here's a PORTABLE HEAVY TABLE WORK BENCH 4... Dec 21 2012, 08:30 PM struckn
[quote name='struckn' post='1787937' date='Dec 21... Dec 22 2012, 06:28 PM mhuber45 i went to our local factory 2nd's building sup... Dec 21 2012, 11:26 AM Brian_Boss All I can add to all the good ideas above is to sa... Dec 21 2012, 05:11 PM Gint Eh... mine has crap on it all the time. Might as ... Dec 21 2012, 05:31 PM Travis Neff :) Dec 22 2012, 11:17 AM stugray
You mean like this: (its sort of a where's w... Dec 22 2012, 04:01 PM Gint :bump: This thread is much too young to die... Dec 23 2012, 11:41 AM Elliot Cannon You can find great ideas here. http://www.garag... Dec 23 2012, 12:16 PM euro911 Yeah. Here you go ... roll away and bench in one m... Dec 23 2012, 01:29 PM jfort finally just got back on line to see if anyone res... Dec 27 2012, 02:26 PM rfuerst911sc Built mine out of 2x6's and over 16 ' long... Dec 28 2012, 04:58 AM 7TPorsh how about some shelving and cabinet ideas? I have... Dec 28 2012, 12:33 PM euro911 If you're on a budget and just need some inexp... Dec 28 2012, 09:05 PM cwpeden Down the street from my place is a government surp... Jan 8 2013, 11:08 PM Michelj13 Here is mine. A little messy, but surprising what ... Jan 9 2013, 09:48 AM 7TPorsh I love this thread. Someone should start on on gar... Jan 9 2013, 10:13 AM charliew I picked up a good metal bench with a top shelf fr... Jan 9 2013, 03:23 PM montoya 73 2.0 I needed a desk but wanted a workbench so I built ... Jan 9 2013, 07:29 PM Gint This thread... influenced me to clean up my bench ... Jan 9 2013, 11:16 PM PanelBilly Find a local office furniture manufacturer. They... Jan 10 2013, 12:26 AM euro911 Long overdue here. Not far behind you, Mike :idea:... Jan 10 2013, 12:29 AM stateofidleness looks like a '78/'79ish Peavey Mace VT Ser... Jan 10 2013, 12:35 AM euro911 looks like a '78/'79ish Peavey Mace VT Ser... Jan 10 2013, 01:08 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 13th July 2025 - 10:05 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.