 Which taco plate seal do I need? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| last337 |
 Jan 10 2013, 11:39 AM
Post
#1
|
|
Member  Group: Members Posts: 421 Joined: 4-December 12 From: New Orleans Member No.: 15,221 Region Association: None  |
I am going to try to fix a leak on the oil temp sender but I havent taken it apart yet. I am ordering a new sending unit as well. I am confused b/c Pelican has two different ones; one being listed as for 1.7 and 1.8 and the other Im assuming for 2.0.
The problem is that this is what my sending unit looks like from bottom:   Which looks like it will take this gasket which Pelican lists as the 1.7, 1.8 gasket  This is the other one they have listed. Do I need both to fix that?  |
   |
 
|
  |
Replies
| last337 |
Jan 10 2013, 12:33 PM
Post
#2
|
|
Member Group: Members Posts: 421 Joined: 4-December 12 From: New Orleans Member No.: 15,221 Region Association: None |
Nevermind, I figured out that I need both. The o-ring goes on sending unit and gasket on taco plate. Duh (IMG:style_emoticons/default/wacko.gif)
|
|
|
|
| luskesq |
Jan 10 2013, 01:05 PM
Post
#3
|
|
Member Group: Members Posts: 276 Joined: 24-October 10 From: Fresno, CA Member No.: 12,303 Region Association: Central California |
QUOTE(last337 @ Jan 10 2013, 10:33 AM)  Nevermind, I figured out that I need both. The o-ring goes on sending unit and gasket on taco plate. Duh (IMG:style_emoticons/default/wacko.gif) Well, you are partially correct. What you need are 2 – 6mm copper crush washers prt# N012803-2, sender crush washer prt# 900-123-007-30, gasket that goes between the two plates 039-101-287 and o-ring prt #021 101 269 A that goes between the taco plate and engine case (not the sending unit. Your pic doesn't show the cover plate that goes on top of the taco plate, then gasket, then plate. Remember not to overtighten. Keith |
|
|
|
| last337 |
Jan 10 2013, 02:04 PM
Post
#4
|
|
Member Group: Members Posts: 421 Joined: 4-December 12 From: New Orleans Member No.: 15,221 Region Association: None |
QUOTE(luskesq @ Jan 10 2013, 01:05 PM) QUOTE(last337 @ Jan 10 2013, 10:33 AM) Nevermind, I figured out that I need both. The o-ring goes on sending unit and gasket on taco plate. Duh (IMG:style_emoticons/default/wacko.gif) Well, you are partially correct. What you need are 2 – 6mm copper crush washers prt# N012803-2, sender crush washer prt# 900-123-007-30, gasket that goes between the two plates 039-101-287 and o-ring prt #021 101 269 A that goes between the taco plate and engine case (not the sending unit. Your pic doesn't show the cover plate that goes on top of the taco plate, then gasket, then plate. Remember not to overtighten. Keith I got everything but the sender crush washer you stated. In the catalog it is listed for a 911. My sender is bad so I ordered a new one prt#323-055-M82. Is that incorrect? That is what the guys at Pelican said I needed. |
|
|
|
Posts in this topic
last337 Which taco plate seal do I need? Jan 10 2013, 11:39 AM
Dave_Darling What sender you need depends on what gauge you hav... Jan 10 2013, 04:04 PM 7TPorsh That sender is in there backwards, right? Jan 10 2013, 04:11 PM
luskesq
That sender is in there backwards, right?
No.
K... Jan 10 2013, 04:21 PM luskesq Dave is correct in that the needle with a mismatch... Jan 10 2013, 04:18 PM Valy I think you got the wrong sensor. The one you need... Jan 10 2013, 04:26 PM |
4 User(s) are reading this topic (4 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th May 2025 - 04:53 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.