 Refurbish hydraulic lifters with new springs? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| AE354803 |
 Jan 16 2013, 05:40 PM
Post
#1
|
|
Member  Group: Members Posts: 232 Joined: 13-August 12 From: Southern California Member No.: 14,801 Region Association: Southern California  |
I have a webcam hydraulic cam and lifters in my 2.0 type IV, I am going to refurbish the lifters and figured I would replace the internals of the lifters while I was in there.
The purpose would be to squeeze more life out of the lifters before I have to crack the case open (at which point in time I will replace the cam and lifters with solid versions). I will replace only the springs and keep the two pieces of the body and the original ball check valve. Does anyone have any advice on this? I am going to clean up the old lifters regardless since I suspect they are not filling correctly due to valvetrain noise, however I'm not sure that replacing the internals would be appropriate? It should avoid the issue with having the lifter surfaces and cam break in together by keeping the original surfaces. I've also considered the possibility of keeping only the part of the original lifter that mates with the cam and replacing the internals and the other part of the body. However I believe due to the mating tolerances in the manufacturing of lifters that this might be a bad move. Thanks for any help. |
   |
 
|
  |
Replies
| Tom |
Jan 16 2013, 07:20 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,139 Joined: 21-August 05 From: Port Orchard, WA 98367 Member No.: 4,626 Region Association: None |
I think you already know this, but just to be sure, keep each lifter identified as to which place it goes.
Tom |
|
|
|
| AE354803 |
Jan 16 2013, 07:33 PM
Post
#3
|
|
Member Group: Members Posts: 232 Joined: 13-August 12 From: Southern California Member No.: 14,801 Region Association: Southern California |
QUOTE(Tom @ Jan 16 2013, 05:20 PM)  I think you already know this, but just to be sure, keep each lifter identified as to which place it goes. Tom Yeah, I'll be keeping track closely. Any input on my proposed spring replacement plan? |
|
|
|
Posts in this topic
AE354803 Refurbish hydraulic lifters with new springs? Jan 16 2013, 05:40 PM
rjames If this is all based on valve train noise, have yo... Jan 16 2013, 06:05 PM
AE354803
If this is all based on valve train noise, have y... Jan 16 2013, 06:20 PM messix my under standing is that the spring in the lifter... Jan 16 2013, 07:57 PM messix where have you found a source for the internal par... Jan 16 2013, 08:00 PM AE354803
where have you found a source for the internal pa... Jan 16 2013, 09:10 PM phatnine11
where have you found a source for the internal p... Jan 16 2013, 09:25 PM AE354803
[quote name='AE354803' post='1803778' date='Jan 1... Jan 16 2013, 09:39 PM mepstein So why not go new on the lifters and cam? Jan 16 2013, 09:42 PM AE354803
So why not go new on the lifters and cam?
I pl... Jan 16 2013, 09:56 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 29th May 2024 - 03:15 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.