 914-6 Header drawing |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| DEC |
 Jan 13 2013, 07:33 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 630 Joined: 10-November 05 From: Rehburg Member No.: 5,104 Region Association: Germany 
 |
Hi,
Has anyone a drawing for the 914-6 Headers with or w/o heat exchangers? In the best case with dimensions. I must build my own ones. Thanks |
   |
 
|
  |
Replies
| RON S. |
Jan 20 2013, 08:24 AM
Post
#2
|
|
9140430841, FINALLY RUNNING Group: Members Posts: 1,212 Joined: 22-May 03 From: WALTERBORO,S.C. Member No.: 724 Region Association: South East States |
QUOTE(carr914 @ Jan 17 2013, 03:31 AM)  I could get you some rough dimensions off these I'm not trying to Hijack the thread, but T.C. what do you happen to know what BRAND of headers those are?? I have an old set of those hanging on the wall, and have never know the maker. |
|
|
|
| Luke M |
Jan 20 2013, 09:24 AM
Post
#3
|
|
Senior Member Group: Members Posts: 1,374 Joined: 8-February 05 From: WNY Member No.: 3,574 Region Association: North East States
|
QUOTE(RON S. @ Jan 20 2013, 07:24 AM) QUOTE(carr914 @ Jan 17 2013, 03:31 AM) I could get you some rough dimensions off these I'm not trying to Hijack the thread, but T.C. what do you happen to know what BRAND of headers those are?? I have an old set of those hanging on the wall, and have never know the maker. Hi Ron, If you decide to sell your headers let me know. I'm looking for a pr. for my 914-6 2.7 RS build. Think 1 5/8 '' is what I need but have heard others say 1 1/2 '' ID maybe best for my setup. Luke |
|
|
|
Posts in this topic
DEC 914-6 Header drawing Jan 13 2013, 07:33 AM
DEC :bump:
no one? Jan 17 2013, 04:03 AM carr914 I could get you some rough dimensions off these
Jan 17 2013, 04:31 AM DEC Hi T.C.
That would be great
Thx Jan 17 2013, 08:23 AM larryM why not just take a set of 911 headers & cut ... Jan 19 2013, 11:58 PM brant I'm pretty sure that those are euro headers Jan 20 2013, 08:26 AM
larryM I have 2 sets of this "flat collector" s... Jan 20 2013, 11:17 AM carr914
I could get you some rough dimensions off these
... Jan 20 2013, 10:10 AM brant euro is a brand made in I believe nevada.
George N... Jan 20 2013, 11:23 PM carr914 Wilco, Sorry for the Delay, I had gotten them out,... Feb 1 2013, 11:18 AM sixnotfour Those headers look like Triads.
http://www.triadwe... Feb 1 2013, 11:34 AM Dave_Darling Not quite, the tube for the forward cylinder on th... Feb 1 2013, 01:56 PM brant George Nobel, european racing....
its like I'm... Feb 1 2013, 02:18 PM SLITS
its like I'm invisible here
brant
Who is ... Feb 2 2013, 09:09 AM brant
its like I'm invisible here
brant
Who is... Feb 4 2013, 12:13 PM sixnotfour Did somebody just reply ?? Does George make two st... Feb 1 2013, 04:53 PM DEC T.C.
Many thanks for the measurement.
That's h... Feb 2 2013, 04:52 AM Luke M
Did somebody just reply ?? Does George make two s... Feb 2 2013, 09:36 AM carr914 :thumbsup: Feb 2 2013, 04:55 AM John I heard from my dad that George Narbel of European... Feb 4 2013, 10:05 PM sixnotfour RIP George Narbel
I just received this Email:
Hi... Feb 4 2013, 10:08 PM Eric_Shea Has anybody heard from Brant lately? :confused: Feb 4 2013, 10:19 PM brant I used to race wheel to wheel with Hank Godfredson... Feb 4 2013, 11:56 PM euro911 I've shrunk more than an inch within the past ... Feb 5 2013, 01:26 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 08:32 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.