 2056 Build |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| yeahmag |
 Feb 2 2012, 12:49 AM
Post
#1
|
|
Advanced Member  Group: Members Posts: 2,468 Joined: 18-April 05 From: Pasadena, CA Member No.: 3,946 Region Association: Southern California 
 |
Installed crank, gears, cam, and rods. Dry fit CB's dry sump pump and modified the tang and clearanced drive tang boss.
 |
   |
 
|
  |
Replies
| yeahmag |
Mar 5 2013, 12:50 AM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,468 Joined: 18-April 05 From: Pasadena, CA Member No.: 3,946 Region Association: Southern California
|
I've actually read more than once that filling the oil filter makes it harder to prime the system, but I neglected to mention that the initial prime will have the oil filter ***off*** until I see oil squirting out. And yup, plugs are out. I have a giant, deep cell battery that I'll be using to turn her over with initially to save my little "red top".
|
|
|
|
| mrbubblehead |
Mar 5 2013, 01:19 AM
Post
#3
|
|
Twodollardoug Group: Members Posts: 1,155 Joined: 17-December 10 From: calimesa ca. Member No.: 12,492 Region Association: Southern California |
QUOTE(yeahmag @ Mar 4 2013, 10:50 PM)  I've actually read more than once that filling the oil filter makes it harder to prime the system, but I neglected to mention that the initial prime will have the oil filter ***off*** until I see oil squirting out. And yup, plugs are out. I have a giant, deep cell battery that I'll be using to turn her over with initially to save my little "red top". i thought you were using a remote filter. |
|
|
|
Posts in this topic
yeahmag 2056 Build Feb 2 2012, 12:49 AM
RobW
Installed crank, gears, cam, and rods. Dry fit CB... Feb 2 2012, 01:01 AM ThePaintedMan Cool! Wish I had the guts to attempt a rebuild... Feb 2 2012, 06:43 AM jaxdream Will the fan housing bolt up / clear the new pump ... Feb 2 2012, 09:06 AM mrbubblehead what are you going to do about your engine mounts? Feb 2 2012, 09:52 AM yeahmag I will need to modify the fan housing to clear the... Feb 2 2012, 10:46 AM mrbubblehead you are one step ahead of me. i am doing the same ... Feb 2 2012, 03:55 PM yeahmag I ground about 2mm off that pump. Maybe more. I al... Feb 2 2012, 04:01 PM mrbubblehead since im not using the stock oil cooler or stock o... Feb 2 2012, 04:16 PM yeahmag How are you routing the oil for the pressure stage... Feb 2 2012, 04:19 PM mrbubblehead i used this diagram http://www.914world.com/bbs2/u... Feb 2 2012, 06:18 PM
Valy
i used this diagram http://www.914world.com/bbs2/... Feb 2 2012, 11:20 PM yeahmag Here are pictures of the pistons after going throu... Feb 2 2012, 09:41 PM jmill :agree:
I was thinking the same thing. Somehow ... Feb 3 2012, 07:07 PM mrbubblehead
:agree:
I was thinking the same thing. Somehow... Feb 3 2012, 07:22 PM Woody You are going to love that engine. :Qarl: :beer2... Feb 3 2012, 07:48 PM mrbubblehead any more progress yeahman? do you know what you ar... Feb 4 2012, 04:18 PM yeahmag Been cleaning parts like mad. Finally ready to clo... Feb 14 2012, 11:32 AM yeahmag OK. The long block is together and I'm startin... May 24 2012, 12:22 PM yeahmag
After the copper spray to help with the carbon s... May 24 2012, 12:23 PM yeahmag
Long block together (more or less). May 24 2012, 12:24 PM yeahmag
Ported the hell out of the CB Dry Sump Pump and ... May 24 2012, 12:25 PM Cupomeat
Ported the hell out of the CB Dry Sump Pump and... Nov 27 2012, 09:44 AM yeahmag
Shot of the heads with Jakes "super" o... May 24 2012, 12:26 PM Valy Those studs look to short to me.
And it looks to m... May 24 2012, 01:39 PM yeahmag The nuts are just there to keep the rockers from f... May 24 2012, 02:10 PM yeahmag Jake appears to like where I have my valve train g... May 29 2012, 06:05 PM yeahmag Measuring my pushrod tips using a flat table and a... Jun 6 2012, 12:19 PM Valy I would not measure them this way. Error is much h... Jun 6 2012, 03:40 PM yeahmag Nah... The rig is designed for telescopes and is o... Jun 6 2012, 04:14 PM yeahmag Here is a wider shot so you get a better feel for ... Jun 6 2012, 04:16 PM Valy The cost of the measuring equipment doesn't be... Jun 6 2012, 04:24 PM yeahmag I don't want to debat this too much, but this ... Jun 6 2012, 04:42 PM Valy
I don't want to debat this too much, but this... Jun 6 2012, 05:39 PM yeahmag This weekend I finished my valve train. I ended up... Jun 11 2012, 12:22 PM yeahmag While not quite part of the engine build I thought... Aug 16 2012, 11:19 AM yeahmag It's been quite a while, but I have been worki... Nov 5 2012, 11:47 AM FourBlades Cool engine build! :Qarl:
John Nov 5 2012, 12:30 PM yeahmag Forgot to show the port matching of the CB manifol... Nov 5 2012, 04:59 PM yeahmag A few more... I have the scavenge line run up the ... Nov 25 2012, 09:07 PM yeahmag RE: 2056 Build Nov 25 2012, 09:08 PM 396 Cool engine build- oh thanks for the education too... Nov 27 2012, 09:00 AM yeahmag Just the two lowers. Nov 27 2012, 10:39 AM yeahmag Some craptastic iPhone photos of the progress. Pas... Dec 11 2012, 06:04 PM mrbubblehead looks good. what size is that? -8, -10? Dec 11 2012, 07:15 PM yeahmag -10 on the scavenge side. -12 for most of the run,... Dec 11 2012, 07:31 PM Gint Nice! When do you fire it? Dec 11 2012, 07:39 PM pete-stevers how did you bend the oil cooler? Dec 11 2012, 11:20 PM yeahmag I bent the cooler in a press supporting it with 2x... Dec 12 2012, 10:56 AM 914_teener
I bent the cooler in a press supporting it with 2... Dec 14 2012, 02:22 PM yeahmag Soon they will be packed full of DOT-R rubber piec... Dec 14 2012, 04:58 PM yeahmag Here are some pic's of my mock up of the tank,... Jan 30 2013, 12:38 PM mrbubblehead nice yeamag. i did the same thing with the T fitti... Jan 30 2013, 07:26 PM yeahmag Good idea! Not sure it has any higher probabil... Jan 30 2013, 08:23 PM mrbubblehead your right. piece of mind i guess. Jan 30 2013, 08:25 PM yeahmag And passenger side is finally done.
Feb 10 2013, 10:59 PM mrbubblehead looks good yeamag. those an fittings sure get expe... Feb 10 2013, 11:35 PM yeahmag ...and yet more fittings to be ordered.
Feb 14 2013, 01:42 PM mrbubblehead that looks awesome bro. im glad summit has the ret... Feb 14 2013, 02:43 PM yeahmag Got a little bit more done. Been thrashing for a f... Feb 25 2013, 12:51 AM yeahmag Really just a matter of making it look good and pu... Mar 4 2013, 10:53 PM yeahmag ...and if anybody has any words of wisdom how to p... Mar 4 2013, 11:10 PM mrbubblehead good luck bro. sounds like a good plan. the only t... Mar 4 2013, 11:55 PM yeahmag Nope. I did remove the bypass and weld it shut in ... Mar 5 2013, 10:20 AM mrbubblehead mine took alot of cranking to get the light to go ... Mar 5 2013, 12:10 PM Racer Chris Aaron,
Did you grease the gears in the pump to hel... Mar 5 2013, 12:32 PM yeahmag No. I've had bad luck with that in the past wi... Mar 5 2013, 12:37 PM Racer Chris I think the type of grease used is critical to tha... Mar 5 2013, 12:51 PM yeahmag Knowing me I used wheel bearing grease and screwed... Mar 5 2013, 12:53 PM dfelz I like your set up a lot, looks really good. are y... Mar 5 2013, 05:36 PM yeahmag Yes. No cutting of the body. Mar 5 2013, 05:46 PM dfelz Very cool, i saw you had a CB dry sump pump, are t... Mar 5 2013, 06:09 PM Racer Chris
... a CB dry sump pump, are the aftermarket pumps... Mar 5 2013, 08:04 PM yeahmag Just a quick update. Priming the system was no har... Mar 11 2013, 09:59 AM yeahmag Drove it in to work yesterday and man did that fee... Apr 3 2013, 11:07 AM yeahmag First long distance outing was driving to Cal Spee... Apr 9 2013, 10:52 AM yeahmag Had some minor surgery on my throat last Monday, s... Apr 24 2013, 09:17 PM yeahmag It did make a "squeak" that seemed to be... Apr 24 2013, 09:24 PM worn
It did make a "squeak" that seemed to b... Apr 30 2013, 08:01 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 24th October 2025 - 08:16 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.