 Pedal area rust |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| mramber |
 Jun 29 2013, 02:48 PM
Post
#1
|
|
Member  Group: Members Posts: 87 Joined: 14-April 13 From: Minneapolis, MN Member No.: 15,768 Region Association: Upper MidWest  |
So today I was going to put in a new gas pedal since the old one wobbled and the hinge was shot. First indication of trouble was that the bolts would not come out of the old pedal, too rusted. After drilling them out and digging around a bit, I can now see the road from the driver seat. :-(
So what is the best method of repair here? Can I replace the supporting (and very rusted) metal under the floor board? I looked a bit but did not find this part in any diagrams. Who else has seen this issue? Attached thumbnail(s)   
|
   |
 
|
  |
Replies
| mramber |
Jun 29 2013, 06:14 PM
Post
#2
|
|
Member Group: Members Posts: 87 Joined: 14-April 13 From: Minneapolis, MN Member No.: 15,768 Region Association: Upper MidWest |
Thanks for the info, the rest of the pan is fine. I was wondering if the supporting piece below the pan was a part that you could buy. mine is almost all rust.
|
|
|
|
| malcolm2 |
Jun 29 2013, 09:15 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 2,747 Joined: 31-May 11 From: Nashville Member No.: 13,139 Region Association: South East States 
|
QUOTE(mramber @ Jun 29 2013, 07:14 PM)  Thanks for the info, the rest of the pan is fine. I was wondering if the supporting piece below the pan was a part that you could buy. mine is almost all rust. It's not really the carpet you should worry about. All that sound proofing stuff hides LOTS AND LOTS of stuff. Ice pick from underneath. |
|
|
|
Posts in this topic
mramber Pedal area rust Jun 29 2013, 02:48 PM
Cap'n Krusty Call or e-mail restoration design. Good folks to ... Jun 29 2013, 03:00 PM
malcolm2
Call or e-mail restoration design. Good folks to... Jun 29 2013, 03:08 PM 76-914 yep, just ordered something from them yesterday. :... Jun 29 2013, 03:09 PM bulitt Your other option is to post a WTB in the classifi... Jun 29 2013, 03:46 PM t collins Restoration Design Part No. 357
Jun 29 2013, 06:24 PM mepstein Scotty b repaired this area on my car. New reinfor... Jun 29 2013, 07:48 PM mepstein you can always find more rust on a 914 if you know... Jun 29 2013, 09:57 PM mramber Thanks all for the help! I ordered the part f... Jun 30 2013, 05:47 AM rhodyguy as noted, you find probably find more issues if yo... Jun 30 2013, 06:14 AM Bartlett 914
as noted, you find probably find more issues if y... Jun 30 2013, 07:08 AM mr914 I have a cut from bill whitesides that a PO of a p... Jun 30 2013, 09:05 PM mramber My car is back on the road! Thanks everyone f... Jul 22 2013, 06:00 AM sean_v8_914 going deep without fear! lookin good Jul 22 2013, 07:29 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 13th July 2025 - 08:10 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.