 AEM Air Fuel Gauge- Awesome!, Innovate sucks!!!! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| tornik550 |
 Jul 10 2013, 08:04 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,248 Joined: 29-January 07 From: Ohio Member No.: 7,486 Region Association: None  |
For the past year, I have been fighting my innovate lc1 setup. It would work under certain circumstances. I never really trusted the readings. Everything was setup properly and calibrated properly. I just got fed up and got an AEM setup. Installed it, started right up. Turns out that my innovate readings were really inaccurate. I was having a super difficult time tuning my carbs cause I was getting strange readings. Now with the AEM, it turns out that my carbs are pretty close to where they should be (IMG:style_emoticons/default/headbang.gif)
Very please with the AEM setup. |
   |
 
|
  |
Replies
| Mark Henry |
Jul 11 2013, 07:16 AM
Post
#2
|
|
that's what I do! Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada |
How did you mount it?
Was the harness long enough? |
|
|
|
| worn |
Jul 11 2013, 10:06 AM
Post
#3
|
|
can't remember Group: Members Posts: 3,173 Joined: 3-June 11 From: Madison, WI Member No.: 13,152 Region Association: Upper MidWest 
|
QUOTE(Mark Henry @ Jul 11 2013, 05:16 AM)  How did you mount it? Was the harness long enough? I had extra wire. My gauge is mounted on the floor (very bad spot) because I already have a rubber 3 gauge pod full under the dash. It wired in great and I bundled the left over wire for when I make my triple or quad gauge. Then I will move it up to replace the oil pressure and volt meter. The bung went in without a problem and I routed the wire along the clutch cable jacket. I am making headway on dialing in the MPS for the 2056 with higher compression. Without the gauge it would be all over. |
 |
|
Posts in this topic
tornik550 AEM Air Fuel Gauge- Awesome! Jul 10 2013, 08:04 PM
Trekkor Same one I use.
Nice set-up.
KT Jul 10 2013, 08:11 PM brant I've checked my innovate system with an air in... Jul 10 2013, 11:48 PM jim_hoyland What is AEM ? Have a link ? :) Jul 11 2013, 07:03 AM
tornik550
What is AEM ? Have a link ? :)
http://www.aeme... Jul 11 2013, 07:06 AM tornik550
How did you mount it?
Was the harness long enough... Jul 11 2013, 07:54 AM Mark Henry
How did you mount it?
Was the harness long enoug... Jul 11 2013, 11:00 AM worn
[quote name='tornik550' post='1893468' date='Jul ... Jul 11 2013, 11:12 AM iamchappy I may have to convert my LC-1 has been acting up.. Jul 11 2013, 07:36 AM Mark Henry Sorry I did get a reply from PLX... just was hard ... Jul 11 2013, 11:04 AM tornik550 I have a plate in the dash where the radio goes. ... Jul 11 2013, 11:17 AM iamchappy I removed the sensor today, cleaned it up and blew... Jul 11 2013, 11:56 AM worn
I removed the sensor today, cleaned it up and ble... Jul 11 2013, 12:58 PM Mark Henry
I removed the sensor today, cleaned it up and ble... Jul 11 2013, 01:12 PM tornik550 I just received a response from AEM about splicing... Jul 11 2013, 03:22 PM Justinp71 Its been a couple months, any updates?
I like the... Sep 23 2013, 07:54 PM tornik550
Its been a couple months, any updates?
I like th... Sep 23 2013, 08:23 PM DBCooper I had an Innovate LC1 that crapped out after a mon... Sep 23 2013, 08:32 PM Justinp71 Is the AEM cable long enough? Sounds like everyone... Sep 23 2013, 08:42 PM tornik550
Is the AEM cable long enough? Sounds like everyon... Sep 23 2013, 08:52 PM worn
Is the AEM cable long enough? Sounds like everyon... Sep 24 2013, 11:39 AM Justinp71 Got the gauge yesterday, install time... :smash:
... Sep 28 2013, 08:41 AM Justinp71 Got it in, just realized there is a nice hole in t... Sep 29 2013, 05:43 PM GeorgeRud What size is the gauge (2 1/8")? Does it fit... Sep 30 2013, 09:09 AM Java2570 It's 52mm (2 1/16") so it's a pretty ... Sep 30 2013, 10:56 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 16th June 2024 - 07:33 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.