 engine tin removal |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| pda914 |
 Jul 28 2013, 12:45 PM
Post
#1
|
|
Newbie  Group: Members Posts: 40 Joined: 22-July 10 From: Verona WI Member No.: 11,966 Region Association: None  |
Is it at all possible to remove the engine tin over the oil cooler and temp sensor without dropping the engine? I need to get at both the oil cooler top and I need to replace the temperare sensor.
If so what should I look out for? |
   |
 
|
  |
Replies
| stugray |
Jul 28 2013, 08:14 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 3,825 Joined: 17-September 09 From: Longmont, CO Member No.: 10,819 Region Association: None |
I have been experimenting with the innovate TC-4. It can read 4 channels of CHT or EGT, but the readout is still digital.
All it requires is a RS-232 (3-wire) interface and new devices just daisy chain. I know there is a digital input to megasquirt for this purpose because I found others doing this exact reading even though my application is not megasquirt oriented. Stu |
|
|
|
Posts in this topic
pda914 engine tin removal Jul 28 2013, 12:45 PM
914itis Yes you can .
You will have to remove all fuel in... Jul 28 2013, 01:18 PM The Cabinetmaker Two questions.
1. Why do you need access to the ... Jul 28 2013, 03:32 PM pda914 I put a custom fuel injection setup and am using ... Jul 28 2013, 04:10 PM
JamesM
I put a custom fuel injection setup and am using... Jul 29 2013, 12:51 PM pda914 I've noticed general 70-80 deg F swings and oc... Jul 29 2013, 01:28 PM JamesM This could also be partly (or completely) due to t... Jul 30 2013, 04:29 PM Dave_Darling In that case, get both sides. There's likely ... Jul 28 2013, 04:31 PM stugray Why would you :
why wouldnt you just replace it ... Jul 28 2013, 04:39 PM pda914 I will be replacing it with a type K themocouple t... Jul 28 2013, 05:19 PM pda914 I thnk drilling out an old thermister and tring to... Jul 28 2013, 05:36 PM The Cabinetmaker Do you have an other than stock temp sender? Jul 28 2013, 04:45 PM pda914 yes I willl be using a thermocouple not the standa... Jul 28 2013, 05:20 PM stugray
True.
Can the megasquirt read from this digital... Jul 28 2013, 05:28 PM pda914 The megasuirt uses an AD that reads from an anolog... Jul 28 2013, 05:52 PM pda914 Four channels would be nice.... I hope one is rep... Jul 28 2013, 09:40 PM stugray
I havent hooked up the CHT yet or run the engine... Jul 29 2013, 09:18 AM Cap'n Krusty
Is it at all possible to remove the engine tin ov... Jul 29 2013, 10:08 AM The Cabinetmaker " since that event the oil temp has been a ... Jul 29 2013, 12:36 PM pda914 Nope the cylinder head temp (Temp II)
... Jul 29 2013, 01:59 PM The Cabinetmaker
Nope the cylinder head temp (Temp II)
... Jul 30 2013, 06:09 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 14th July 2025 - 04:41 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.