 engine tin removal |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| pda914 |
 Jul 28 2013, 12:45 PM
Post
#1
|
|
Newbie  Group: Members Posts: 40 Joined: 22-July 10 From: Verona WI Member No.: 11,966 Region Association: None  |
Is it at all possible to remove the engine tin over the oil cooler and temp sensor without dropping the engine? I need to get at both the oil cooler top and I need to replace the temperare sensor.
If so what should I look out for? |
   |
 
|
  |
Replies
| stugray |
Jul 29 2013, 09:18 AM
Post
#2
|
|
Advanced Member Group: Members Posts: 3,825 Joined: 17-September 09 From: Longmont, CO Member No.: 10,819 Region Association: None |
QUOTE Do you see much variation in head temp? I havent hooked up the CHT yet or run the engine much since break in. I have been using it to watch EGTs and it works fine. I am currently trying to figure out how to read the digital data stream with a Droid tablet so I can have a generic instrument display. Also - You can get a thermistor that works to 200C: http://www.omega.com/Temperature/pdf/55000.pdf And QUOTE I thnk drilling out an old thermister and tring to glue it back together with some sort of epoxy that can transfer heat in order to get an isolated ground sensor is questionable in its final performance It would work just fine. That is how we install them on spacecraft. The 4-wire measurement is more accurate than the 2-wire measurement, but the source/meter must support it. Stu |
|
|
|
Posts in this topic
pda914 engine tin removal Jul 28 2013, 12:45 PM
914itis Yes you can .
You will have to remove all fuel in... Jul 28 2013, 01:18 PM The Cabinetmaker Two questions.
1. Why do you need access to the ... Jul 28 2013, 03:32 PM pda914 I put a custom fuel injection setup and am using ... Jul 28 2013, 04:10 PM
JamesM
I put a custom fuel injection setup and am using... Jul 29 2013, 12:51 PM pda914 I've noticed general 70-80 deg F swings and oc... Jul 29 2013, 01:28 PM JamesM This could also be partly (or completely) due to t... Jul 30 2013, 04:29 PM Dave_Darling In that case, get both sides. There's likely ... Jul 28 2013, 04:31 PM stugray Why would you :
why wouldnt you just replace it ... Jul 28 2013, 04:39 PM pda914 I will be replacing it with a type K themocouple t... Jul 28 2013, 05:19 PM pda914 I thnk drilling out an old thermister and tring to... Jul 28 2013, 05:36 PM The Cabinetmaker Do you have an other than stock temp sender? Jul 28 2013, 04:45 PM pda914 yes I willl be using a thermocouple not the standa... Jul 28 2013, 05:20 PM stugray
True.
Can the megasquirt read from this digital... Jul 28 2013, 05:28 PM pda914 The megasuirt uses an AD that reads from an anolog... Jul 28 2013, 05:52 PM stugray I have been experimenting with the innovate TC-4. ... Jul 28 2013, 08:14 PM pda914 Four channels would be nice.... I hope one is rep... Jul 28 2013, 09:40 PM Cap'n Krusty
Is it at all possible to remove the engine tin ov... Jul 29 2013, 10:08 AM The Cabinetmaker " since that event the oil temp has been a ... Jul 29 2013, 12:36 PM pda914 Nope the cylinder head temp (Temp II)
... Jul 29 2013, 01:59 PM The Cabinetmaker
Nope the cylinder head temp (Temp II)
... Jul 30 2013, 06:09 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 14th July 2025 - 04:42 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.