 Inner long Chassis Stiff Kit install, the complete photo documentary |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Trekkor |
 Jul 18 2004, 11:44 PM
Post
#1
|
|
I do things...  Group: Members Posts: 7,809 Joined: 2-December 03 From: Napa, Ca Member No.: 1,413 Region Association: Northern California  |
O.K. folks, here it is from start to finish:
First you must remove the seam sealer and body tar from the inside corner of the longs. Attached image(s) 
|
   |
 
|
  |
Replies
| Engman |
Jul 19 2004, 08:13 PM
Post
#2
|
|
Zoisite Group: Benefactors Posts: 1,349 Joined: 25-March 03 From: New Albany, IN Member No.: 475  |
Rear sways - ground to the car (make sure battery and ECU are disconnected) and just wire wheel or gring the edges were you want to weld. You really only need one to start, the others will burn thru after you start to weld. Be sure to touch up with some paint after you are done welding and it has cooled.
M |
|
|
|
Posts in this topic
trekkor Inner long Chassis Stiff Kit install Jul 18 2004, 11:44 PM
trekkor It is very thick in the corners. Jul 18 2004, 11:45 PM trekkor notice the bead of seam sealer that must come out ... Jul 18 2004, 11:48 PM trekkor another Jul 18 2004, 11:49 PM trekkor an air chisel works very well to remove the materi... Jul 18 2004, 11:51 PM trekkor the width of the chisel point using careful, short... Jul 18 2004, 11:53 PM trekkor tar out Jul 18 2004, 11:54 PM trekkor without removal of the seam sealer and tar the she... Jul 18 2004, 11:56 PM trekkor passenger side drops right in. Jul 18 2004, 11:57 PM trekkor driver side in. the area around the e-brake handle... Jul 18 2004, 11:59 PM trekkor more :smash:
I like to grind the edges for a goo... Jul 19 2004, 12:01 AM trekkor the inside corners need to be bent and worked into... Jul 19 2004, 12:03 AM trekkor other side Jul 19 2004, 12:04 AM trekkor back piece in .
3 sided dry fitment. Make sure it ... Jul 19 2004, 12:06 AM trekkor :welder:
put the weld in the hole and burn into t... Jul 19 2004, 12:11 AM trekkor mask off the interior and windows so as not to dam... Jul 19 2004, 12:13 AM jgiroux67 What are the black ovals for that are on the passe... Jul 19 2004, 12:13 AM trekkor driver side and ground down Jul 19 2004, 12:17 AM trekkor back plate Jul 19 2004, 12:18 AM trekkor all three sides tied in :welder: Jul 19 2004, 12:20 AM trekkor corner detail shot Jul 19 2004, 12:21 AM trekkor ready for paint Jul 19 2004, 12:23 AM trekkor paint Jul 19 2004, 12:24 AM trekkor rattle can , daddy :shades: Jul 19 2004, 12:26 AM trekkor spray it Jul 19 2004, 12:27 AM trekkor bird's eye Jul 19 2004, 12:28 AM trekkor The black ovals are tar pieces that cover access h... Jul 19 2004, 12:40 AM RON S. Great job, :trophy:
That is a great documentary o... Jul 19 2004, 04:58 AM sgomes Awesome job both with the welding and the pictoria... Jul 19 2004, 06:38 AM seanery The kit is Engman's Inner Long Reinforcement k... Jul 19 2004, 08:10 AM nebreitling buck toenges How do you think that this "inner" kit compares wi... Jul 19 2004, 01:33 PM bperry Out of curiousity, which welder did you use and di... Jul 19 2004, 04:55 PM kwales I'm still trying to figure out how he welded a... Jul 19 2004, 05:19 PM trekkor Miller wire feeder mig welder.
When the wire hits... Jul 19 2004, 05:26 PM trekkor The secret to good welds on thin material is low v... Jul 19 2004, 05:32 PM seanery Does that have clickstops at each # for power? Min... Jul 19 2004, 05:35 PM trekkor I know it clicks at each interval. I've never ... Jul 19 2004, 05:45 PM Qarl I have a question...
Is there a reason why you di... Jul 19 2004, 05:46 PM trekkor Good question. :idea:
My understanding is that a... Jul 19 2004, 06:11 PM Engman Wow - great pics on the install and testing! T... Jul 19 2004, 06:20 PM Qarl QUOTE
trekkor You could use silicone.
I'm going to do that,... Jul 19 2004, 06:35 PM 9146986 Are these pieces made of coated steel?
My persona... Jul 19 2004, 06:37 PM Engman These have a zinc phosphate coating and then are p... Jul 19 2004, 07:27 PM seanery Hey Mark, what about the ecoating, does it need to... Jul 19 2004, 07:47 PM Engman No ecoat on these puppies. I do run it through the... Jul 19 2004, 08:06 PM seanery I was referring to the other stuff-rear sway bar m... Jul 19 2004, 08:09 PM Brad Roberts Great job Trekkor :clap: Sorry I didnt have time... Jul 19 2004, 09:54 PM soloracer If one is going to install a roll cage would this ... Jul 19 2004, 09:58 PM Brad Roberts redundant at that point...
This is for people who... Jul 19 2004, 10:02 PM Engman A big thank you to Brad and Trekkor! This is a... Jul 19 2004, 10:55 PM Brad Roberts Sooner or later I will build myself a AutoX/track ... Jul 19 2004, 10:59 PM Randal Great Work Mr. T.
Now we know why your car was ... Jul 20 2004, 10:38 AM maf914 KT, Thanks for the great photos and description. ... Jul 20 2004, 11:09 AM J P Stein You will notice... Jul 20 2004, 05:55 PM nsyr how about this made them myself from 14 gauge. Jul 20 2004, 07:30 PM
trekkor Yep. That's the stuff!!
Good job :cla... Jul 20 2004, 10:26 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd May 2025 - 07:00 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.