Stud remover, Yes, I know you can buy this from Snap On |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Stud remover, Yes, I know you can buy this from Snap On |
worn |
Sep 10 2013, 09:56 AM
Post
#1
|
can't remember Group: Members Posts: 3,164 Joined: 3-June 11 From: Madison, WI Member No.: 13,152 Region Association: Upper MidWest |
I wanted to pull the studs from a transmission case so I wouldn't poke my eye out with the darn things and while it wears the magnesium it also shows when there isn't any really left in the threads. there - the excuses, version 1.
So I got 1 bolt and 1 nut and set the lathe for stun, er taper cut. The nut and the bolt are tapered so there is a countersink in the large nut and a fly-head screw look to the bolt. BTW the nut is a loose fit over the bolt - they aren't matched. While I was at it I drilled straight into the top of the bolt to allow for thread tapping. Off the lathe, the hole in the top of the bolt was tapped to fit the stud - this was 8 mm, but I am gunning for 911 head studs eventually. I used a slotting wheel on the angle grinder to make an X cut down the length. Then I added a nut that does fit the bolt. Whoops, didn't go down far enough so another loose nut was added as a spacer. This is what it looked like in action. Unfortunately I pinned a nut to allow for wrenching so it doesn't come apart and the pix aren't so great, but here is the stud. |
sixnotfour |
Sep 10 2013, 02:45 PM
Post
#2
|
914 Wizard Group: Members Posts: 10,436 Joined: 12-September 04 From: Life Elevated..planet UT. Member No.: 2,744 Region Association: Rocky Mountains |
Two nuts tighten agianst each other works good too.
I do have the old snap-on stud and dowel remover, way better than the one they sell now IMHO. |
Nine_14 |
Sep 10 2013, 02:53 PM
Post
#3
|
Member Group: Members Posts: 311 Joined: 30-August 12 From: Germany Member No.: 14,873 Region Association: Germany |
Two nuts tighten agianst each other works good too. (IMG:style_emoticons/default/agree.gif) Why doing it easily when it also works complicated (IMG:style_emoticons/default/dry.gif) |
worn |
Sep 10 2013, 03:01 PM
Post
#4
|
can't remember Group: Members Posts: 3,164 Joined: 3-June 11 From: Madison, WI Member No.: 13,152 Region Association: Upper MidWest |
Two nuts tighten agianst each other works good too. (IMG:style_emoticons/default/agree.gif) Why doing it easily when it also works complicated (IMG:style_emoticons/default/dry.gif) I do that. The stud I showed was going to be distorted by the simple method. I have done that too, where the stud is more than willing to ruin two perfectly nice matching nuts and itself as well, just in order to stay put. And then the vice grips and the torch and the pain and the slow weeping in the corner. Wait, I think I went too far. (IMG:style_emoticons/default/w00t.gif) |
Lo-Fi Version | Time is now: 11th June 2024 - 03:26 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |