 Photograph request-Sideshift transmission detail, of installed clutch cable pulley w/cable attacthed |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| HalfMoon |
 Dec 11 2013, 06:23 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 828 Joined: 13-November 12 From: Shenandoah Junction, WV Member No.: 15,144 Region Association: MidAtlantic Region  |
My PO had a thing rigged up and I want to see the correct installation/gear as I'm finishing the installation of my Dr Evil sorted transmission.
Thanks! David |
   |
 
|
  |
Replies
| Phoenix-MN |
Dec 11 2013, 06:41 PM
Post
#2
|
|
Senior Member Group: Members Posts: 927 Joined: 23-January 04 From: ST. Bonifacius,MN Member No.: 1,590 |
QUOTE(HalfMoon @ Dec 11 2013, 04:23 PM)  My PO had a thing rigged up and I want to see the correct installation/gear as I'm finishing the installation of my Dr Evil sorted transmission. Thanks! David  |
|
|
|
| jcd914 |
Dec 12 2013, 12:43 AM
Post
#3
|
|
Advanced Member Group: Members Posts: 2,081 Joined: 7-February 08 From: Sacramento, CA Member No.: 8,684 Region Association: Northern California |
QUOTE(Phoenix-MN @ Dec 11 2013, 04:41 PM) QUOTE(HalfMoon @ Dec 11 2013, 04:23 PM) My PO had a thing rigged up and I want to see the correct installation/gear as I'm finishing the installation of my Dr Evil sorted transmission. Thanks! David This shows the correct installation of the cable retainer, the "Tab Washer". The boot in this picture should be slipped on to the end of the cable housing and away from the roller. The cable goes thru the eye of the tab washer all the way onto the metal end of the cable housing. Then the metal end of the cable housing slides into the opening in the support bracket. This puts the tab washer between the cable and the support bracket. The tab is then bent around the back of the support bracket and the end is poked out thru the hole in the bracket. This make it so the cable can't slide back out of the support bracket. Then the boot slides on the cable and all the way up on to the metal end of the cable housing, where it helps keep dirt and grit out of you cable. QUOTE(Steve_R @ Dec 11 2013, 10:07 PM) Here's a picture of mine. Steve_R, your tab washer is installed incorrectly. It should be on the other side of the support bracket and the tabe should be coming around from behind the bracket and poking out of the whole it is now poking into. The bottom line is that the tab washers function is to keep the cable from sliding out of the slot in the support bracket and stranding you along the road some where.Some saftey wire could be used, wire ties could be used, an old coat hanger could be used but the tab washer is a nice clean install and what was OE. Jim |
 |
|
Posts in this topic
HalfMoon Photograph request-Sideshift transmission detail Dec 11 2013, 06:23 PM
wndsnd
[quote name='HalfMoon' post='1969364' date='Dec 1... Dec 11 2013, 07:09 PM
HalfMoon
[quote name='HalfMoon' post='1969364' date='Dec ... Dec 11 2013, 07:41 PM David_S I thought that the boot went onto the firewall ??? Dec 11 2013, 07:54 PM wndsnd I am sorry I do not have photo shop so I can put t... Dec 11 2013, 07:58 PM Old Yella
I am sorry I do not have photo shop so I can put ... Dec 11 2013, 09:09 PM Old Yella Here is another post on this forum, please refer t... Dec 11 2013, 09:24 PM wndsnd I'd believe that boot goes at the firewall bef... Dec 11 2013, 09:47 PM HalfMoon Hmm...so after examining another thread photograph... Dec 11 2013, 10:41 PM wndsnd
Hmm...so after examining another thread photograp... Dec 12 2013, 08:00 AM HalfMoon Hmmm....perhaps it's part number 53 on the dia... Dec 11 2013, 10:54 PM Cupomeat
Hmmm....perhaps it's part number 53 on the di... Dec 11 2013, 11:26 PM Steve_R Here's a picture of mine. Dec 12 2013, 12:07 AM HalfMoon Here's a better photograph at Pelican but as y... Dec 11 2013, 11:07 PM Cupomeat This problem vexed me for MANY years until I final... Dec 11 2013, 11:23 PM Cap'n Krusty Well, that's amusing. And creative. And wron... Dec 12 2013, 12:18 AM HalfMoon Terrific input from all!
I think we can close ... Dec 12 2013, 09:02 AM Cap'n Krusty Just one more post to this thread! The tab wa... Dec 12 2013, 10:13 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 31st October 2024 - 06:00 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.