 raised spindels, what has been done before? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| metalmorphosis |
 May 11 2014, 10:03 PM
Post
#1
|
|
Member  Group: Members Posts: 90 Joined: 31-July 12 From: winston-salem nc Member No.: 14,743 Region Association: South East States  |
So I think I want to raise the spindle on the strut tube and I know I've seen some threads about doing this. I did a little searching and didn't find anything useful so I'm hoping you guys can give me some advice or share any links with me. The reason I think I would like to do this is to regain a little suspension travel in the front end. My car is pretty low and currently has no travel to speak of in the front. So I think if I lower the car more by raising the spindles I can lift the car back up using the torsion bars to gain some suspension travel back. Ultimately I want my cars ride height to be about the same as it is now. I'm thinking of raising the spindle 1 inch, is there another standard amount of raise that has been done before? Is there any reason not to do this modification? I assume the tie rods would be fine and all the geometry would be almost the same, right? So what do y'all know about this one?
Attached thumbnail(s) 
|
   |
 
|
  |
Replies
| Elliot Cannon |
May 11 2014, 10:58 PM
Post
#2
|
|
914 Guru Group: Retired Members Posts: 8,487 Joined: 29-December 06 From: Paso Robles Ca. (Central coast) Member No.: 7,407 Region Association: None 
|
My car sits fairly low and I have plenty of suspension travel. With the 17 inch wheels, lower profile tires and low airdam in the front I think it looks lower than it actually is. Most of the raised spindles I thought were on race cars. I don't autocross or race so maybe you have different plans for your car. Post some pics please.
Attached image(s) 
|
|
|
|
Posts in this topic
metalmorphosis raised spindels May 11 2014, 10:03 PM
sixnotfour what diameter wheel and offset is the control on h... May 11 2014, 10:35 PM Dave_Darling Raising the spindles is a relatively-common mod in... May 11 2014, 10:51 PM metalmorphosis My car does have 17" wheels on it, don't ... May 11 2014, 11:15 PM
jaxdream
My car does have 17" wheels on it, don't... May 12 2014, 08:33 AM
Dave_Darling So Dave why would this potentially cause worse bum... May 12 2014, 04:04 PM WLD419 Here's a link , hope this helps, Bill D.
ht... May 12 2014, 04:08 AM dlee6204 http://www.914world.com/bbs2/index.php?sho...11184... May 12 2014, 04:24 AM metalmorphosis Thanks Jack the wheels are 17 x 7 and the tires ar... May 12 2014, 10:15 AM Racer Chris
On that thread where they cut some length out of ... May 12 2014, 10:56 AM tscrihfield Goto my thread in my signature and look at the bot... May 12 2014, 05:17 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 10th May 2025 - 08:20 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.