 More D-Jet, High Idle Lean Mixture |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| ggress |
 May 16 2014, 08:01 PM
Post
#1
|
|
Newbie  Group: Members Posts: 6 Joined: 11-May 14 From: Oregon Member No.: 17,334 Region Association: None  |
Just getting a '74 2.0 running that I purchased few years back. Replaced all fuel lines, vacuum lines, and FI Harness. It runs better than I expected but not good enough.
It idles too fast (1300 / 1400 RPM) considering throttle valve bypass screw is all the way in. Also, it runs lean (using WB A/F meter). I have set the mixture adjustment on the ECU full CW to get mixture around 13.7:1. I think I have covered all the common vacuum leak issues described in other threads. Any suggestions appreciated. I have two specific questions below. 1) Is my ECU P/N correct? The base P/N is correct but not sure what the 090 suffix means. 2) With the throttle valve bypass screw turned in full CW there is still vacuum getting past the screw. Does anybody know if that is normal ? I can put my finger over the port and feel vacuum. Maybe by design it is not meant to provide positive shut off but I don't have enough experience to say one way or the other. Thx   |
   |
 
|
  |
Replies
| JeffBowlsby |
May 17 2014, 08:02 AM
Post
#2
|
|
914 Wiring Harnesses & Beekeeper Group: Members Posts: 8,982 Joined: 7-January 03 From: San Ramon CA Member No.: 104 Region Association: None 
|
Nice to see you here Gary!
Here is one method of checking for leaks - from one of the Bosch manuals. Attached image(s) 
|
|
|
|
Posts in this topic
ggress More D-Jet May 16 2014, 08:01 PM
Montreal914 You need to make sure everything is set properly s... May 16 2014, 08:46 PM Dave_Darling It's normal for air to still get through the b... May 16 2014, 09:00 PM luskesq I had a slightly high idle issue with my 1.7 (1200... May 16 2014, 10:02 PM ggress Thanks for the input !!!
I am famil... May 16 2014, 10:48 PM JawjaPorsche Chasing a vacuum leak is a pain. Have you replace... May 17 2014, 04:56 AM era vulgaris I'm in the same boat as you, except I've g... May 17 2014, 06:29 AM Spoke You can locate vacuum leaks pretty easy with carb ... May 17 2014, 09:40 AM
worn
You can locate vacuum leaks pretty easy with carb... May 17 2014, 12:25 PM ggress I agree, it has to be a vacuum leak /s of some kin... May 18 2014, 10:59 AM Racer Chris
2) This one has me scratching my head. Is it pos... May 18 2014, 11:36 AM 914_teener You can take out the plenum and use a eak penetran... May 18 2014, 03:47 PM boxsterfan Change your intake runner boots, intake manifold g... May 18 2014, 04:20 PM boxsterfan Change your intake runner boots, intake manifold g... May 18 2014, 04:20 PM ggress Everything is new, injectors / seals, FI harness, ... May 18 2014, 05:38 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st August 2025 - 06:25 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.