 Test your 914 Tech Knowledge!, Possible Future Parade 914 Tech Quiz Questions |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| JeffBowlsby |
 Jul 1 2014, 07:08 PM
Post
#1
|
|
914 Wiring Harnesses & Beekeeper  Group: Members Posts: 8,982 Joined: 7-January 03 From: San Ramon CA Member No.: 104 Region Association: None 
 |
1. For a 1975-76 California-market 914, a flashing EGR dash light means what?
a. The EGR valve has become too hot. b. The 30KMI service interval for the EGR system has been reached. c. The EGR dash light does not flash when it activates. d. The EGR system needs to be removed to keep this from happening again Answer: C. The EGR light is only a steady light at 30KMI intervals. The CAT light is also steady at 30KMI and flashes when it overheats. 2. How many different factory 914/4 oil temperature sender wires (green/black stripe) were available through all model years, excluding the chassis harness wiring? a. 1 b. 2 c. 3 d. 4 Answer: C. 1970-71, sender to ignition harness. 72=none. 1973-76, sender to chassis harness for center console gauge, and center console to dash area for non-center console cars. 3. The 914’s removable hardtops are identical across all model years. a. True b. False Answer: False. Early and late styles are different and not interchangeable Post more Questions/Answers that might make good Parade 914 tech quiz questions - Share your knowledge. |
   |
 
|
  |
Replies
| JeffBowlsby |
Jul 2 2014, 10:39 AM
Post
#2
|
|
914 Wiring Harnesses & Beekeeper Group: Members Posts: 8,982 Joined: 7-January 03 From: San Ramon CA Member No.: 104 Region Association: None
|
What...no one wants to play? Here is another:
1. To install H4 headlights into a USA 914, the original factory rubber sealing boot must be replaced also. a. True b. False Answer: True. The factory manual describes replacing the original black rubber boot with a red rubber boot and the transparent electrical connector housing with a polyamide (nylon) connector housing for better heat resistance. |
|
|
|
| bdstone914 |
Jul 2 2014, 11:00 PM
Post
#3
|
|
bdstone914 Group: Members Posts: 5,061 Joined: 8-November 03 From: Riverside CA Member No.: 1,319 |
QUOTE(Jeff Bowlsby @ Jul 2 2014, 09:39 AM)  What...no one wants to play? Here is another: 1. To install H4 headlights into a USA 914, the original factory rubber sealing boot must be replaced also. a. True b. False Answer: True. The factory manual describes replacing the original black rubber boot with a red rubber boot and the transparent electrical connector housing with a polyamide (nylon) connector housing for better heat resistance. What original rubber boot? Never seen one. |
 |
|
Posts in this topic
Jeff Bowlsby Test your 914 Tech Knowledge! Jul 1 2014, 07:08 PM
r_towle First question made me mad at you .
:) Jul 1 2014, 07:14 PM Dave_Darling I think most of these so far are a bit too fussy f... Jul 2 2014, 11:40 AM bandjoey The original Cabin Light has a chrome edge and is ... Jul 2 2014, 06:59 PM
914_teener
The original Cabin Light has a chrome edge and is... Jul 3 2014, 08:46 AM bandjoey
The original Cabin Light has a chrome edge and i... Jul 3 2014, 10:01 AM Jeff Bowlsby This one... Jul 2 2014, 11:37 PM Jeff Bowlsby This one... Jul 2 2014, 11:37 PM ClayPerrine Here are two from some tech quizzes that I wrote i... Jul 3 2014, 07:42 AM bandjoey
Here are two from some tech quizzes that I wrote ... Jul 3 2014, 09:58 AM Dave_Darling
You and a friend go to look at a 914 /6 you saw i... Jul 3 2014, 11:42 AM 76-914 How many cuss words does it require to install spr... Jul 3 2014, 07:46 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st August 2025 - 05:48 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.