 Speedo cable, Boot wrong |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jeffdon |
 Aug 23 2014, 02:53 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,094 Joined: 24-October 06 From: oakland, ca Member No.: 7,087 Region Association: None  |
Here is a pic of my new speedo cable. This is the tranny end. The boot appears to be on the wrong way. Got this from the bird. Any one else have this issue? I am starting to loose faith in these guys.
 |
   |
 
|
  |
Replies
| Jacco |
Sep 5 2014, 02:06 PM
Post
#2
|
|
Designated Dutchman Group: Members Posts: 194 Joined: 23-February 04 From: the Netherlands Member No.: 1,703 Region Association: Europe |
Had the same experiece with the speedo cable.
Asked the question about the rubber boots to a couple of european resellers with pictures as above, comes down to this: factory claims they are exactly according to factory drawing. I decided to heat the rubber in hot water and carefully removed it to place it back correctly. Jacco |
|
|
|
| mepstein |
Sep 6 2014, 07:23 AM
Post
#3
|
|
914-6 GT in waiting Group: Members Posts: 20,217 Joined: 19-September 09 From: Landenberg, PA/Wilmington, DE Member No.: 10,825 Region Association: MidAtlantic Region 
|
QUOTE(Jacco @ Sep 5 2014, 04:06 PM)  Had the same experiece with the speedo cable. Asked the question about the rubber boots to a couple of european resellers with pictures as above, comes down to this: factory claims they are exactly according to factory drawing. I decided to heat the rubber in hot water and carefully removed it to place it back correctly. Jacco Good idea |
 |
|
Posts in this topic
jeffdon Speedo cable Aug 23 2014, 02:53 PM
Dr Evil How is that on the wrong way? It is supposed to sl... Aug 23 2014, 03:19 PM mepstein its correct. you'll see when you install. Aug 23 2014, 03:33 PM
jeffdon
its correct. you'll see when you install.
H... Aug 23 2014, 03:40 PM Dr Evil Jeff, I am not following you. You dont take it off... Aug 23 2014, 03:48 PM JawjaPorsche
Jeff, I am not following you. You dont take it of... Aug 23 2014, 04:30 PM jeffdon
Jeff, I am not following you. You dont take it of... Aug 23 2014, 06:25 PM mepstein
Jeff, I am not following you. You dont take it o... Aug 23 2014, 06:44 PM jeffdon
[quote name='jeffdon' post='2077336' date='Aug 23... Aug 23 2014, 08:05 PM bluhun
[quote name='jeffdon' post='2077336' date='Aug 2... Aug 24 2014, 01:51 AM bluhun
[quote name='jeffdon' post='2077336' date='Aug 2... Aug 24 2014, 02:05 AM bluhun
[quote name='jeffdon' post='2077336' date='Aug 2... Aug 24 2014, 02:20 AM jeffdon
[quote name='jeffdon' post='2077372' date='Aug 23... Aug 24 2014, 06:41 AM bluhun
[quote name='jeffdon' post='2077372' date='Aug 2... Aug 24 2014, 09:14 PM Dr Evil Here is the official pic from the PET. The lower p... Aug 25 2014, 08:37 AM Dr Evil OK, I just replaced my speedo cable with a new Gem... Sep 5 2014, 06:50 AM eyesright I have bought two cables for two cars in the past ... Sep 5 2014, 08:36 AM Dr Evil I bet if we get Glenns attention to this thread he... Sep 5 2014, 09:15 AM rgalla9146 I don't know about the bulkhead boot.
I do k... Sep 5 2014, 07:56 PM ClayPerrine The boots have been reversed on the cables for yea... Sep 6 2014, 07:09 AM Jeffs9146
The boots have been reversed on the cables for ye... Sep 6 2014, 09:44 AM rgalla9146 The problem is not with the boots. It's a hard... Sep 6 2014, 08:15 AM jeffdon How is one supposed to get a proper cable? Sep 6 2014, 09:55 AM mepstein Is it worth keeping the old parts to remake a new ... Sep 6 2014, 10:06 AM rgalla9146 Sure, remove the angle drive end from the sheath o... Sep 6 2014, 10:49 AM jeffdon
Sure, remove the angle drive end from the sheath ... Sep 6 2014, 01:53 PM rgalla9146 ......my response was a bit tongue-in-cheek.
may... Sep 6 2014, 02:43 PM bluhun
......my response was a bit tongue-in-cheek.
ma... Sep 6 2014, 06:08 PM jeffdon
......my response was a bit tongue-in-cheek.
m... Sep 6 2014, 11:08 PM jeffdon BUMP
Anyone come up with a source for a proper ca... Sep 17 2014, 08:56 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th November 2025 - 11:01 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.