 How to Get Engine onto Engine Stand? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| VWTortuga336 |
 Oct 29 2014, 08:16 AM
Post
#1
|
|
Member  Group: Members Posts: 285 Joined: 5-October 14 From: Kansas City, Missouri Member No.: 17,979 Region Association: None  |
This may have already been covered, but I haven't had any luck figuring my problem out. I've got my engine pulled, tranny separated and the engine is on my ATV jack. I just bought an engine stand and now I can't figure out how to mount the engine to it (IMG:style_emoticons/default/headbang.gif) The ATV jack won't raise high enough to get all 4 mounting points to line up. And, the base of the stand won't allow the stand to get close enough to the engine, due to the base of the jack.
Anyone have any tricks they could share? Attached thumbnail(s) 
|
   |
 
|
  |
Replies
| r_towle |
Oct 29 2014, 08:31 AM
Post
#2
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States 
|
Seeing as you have a three wheel engine stand, you could raise and block the motor, then raise and block the jack, leaving a hole in the middle for the engine stand leg.
Keep doing that until it's at the right height to allow you to slide the engine stand under the jack, right up the the motor. Remove the heat exchangers Turn the motor sideways on that lift to avoid the handle. |
|
|
|
Posts in this topic
VWTortuga336 How to Get Engine onto Engine Stand? Oct 29 2014, 08:16 AM
type47 You could take the yoke off the stand and over to ... Oct 29 2014, 08:22 AM bandjoey and a few friends with muscles! Ebay has seve... Oct 29 2014, 08:24 AM r_towle First off you need a porsche/VW head for the engin... Oct 29 2014, 08:25 AM VWTortuga336 Thanks for all the suggestions. Anyone in the KC,... Oct 29 2014, 09:34 AM
McMark
Thanks for all the suggestions. Anyone in the KC... Oct 29 2014, 10:21 AM Phoenix914
Thanks for all the suggestions. Anyone in the K... Oct 29 2014, 10:26 AM stugray Mount the yoke to the engine first.
Leave the engi... Oct 29 2014, 10:40 AM bandjoey The cheap one for the once in 10 year rebuilder. Oct 29 2014, 10:44 AM 914Sixer I put a sling around the engine. Install engine ... Oct 29 2014, 04:22 PM maf914
I
Throw a chain around tree limb, attach wench, a... Oct 30 2014, 05:46 AM CatDaddy60 I used to pick up the engine after bolting the yol... Oct 29 2014, 04:48 PM DBCooper This thread is great. I've always just muscle... Oct 29 2014, 05:34 PM r_towle Hate to say it, but now that I have a lift I have ... Oct 29 2014, 05:54 PM 914Sixer Sometimes I my fingers don"t match what I am ... Oct 30 2014, 06:07 AM Edchina
I use a chain hoist and an attachement to handle... Oct 30 2014, 06:33 AM carr914
Hate to say it, but now that I have a lift I have... Oct 30 2014, 06:53 AM Vacca Rabite Hand crank winch and a pulley hanging off a rafter... Oct 30 2014, 08:16 PM mapguy I got the cheap chain hoist at HF and use one of t... Oct 30 2014, 09:49 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 11:42 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.