 cv joints for914/6 |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| altitude411 |
 Dec 3 2014, 01:22 AM
Post
#1
|
|
I drove my 6 into a tree  Group: Members Posts: 1,306 Joined: 21-September 14 From: montana Member No.: 17,932 Region Association: Rocky Mountains 
 |
Can someone school me on axle shafts on a '70/6? Are they the same as the 911? Can I replace the CV's on my car or do I need to buy a complete axle shaft assembly.
|
   |
 
|
  |
Replies
| pcar916 |
Dec 3 2014, 09:52 AM
Post
#2
|
|
Is that a Lola? Group: Members Posts: 1,523 Joined: 2-June 05 From: Little Rock, AR Member No.: 4,188 Region Association: None
|
The 914-6 axles are longer than 911 axles, but have the 911 spline-count. 914-6 CV's are the same diameter as 914-4 with a 911-splined inner race.
If you want to remain stock, a complete axle is a possibility, or you can use 914-4 CV's and an aftermarket, free-floating axle like SwayAway that's the right length and with 914-4 splines... which are the same as the 944 spline-count BTW. Other's here will chime in with vendors and availability. Good luck |
|
|
|
| type47 |
Dec 3 2014, 11:29 AM
Post
#3
|
|
Viermeister Group: Members Posts: 4,254 Joined: 7-August 03 From: Vienna, VA Member No.: 994 Region Association: MidAtlantic Region |
QUOTE(pcar916 @ Dec 3 2014, 07:52 AM)  If you want to remain stock, a complete axle is a possibility, or you can use 914-4 CV's and an aftermarket, free-floating axle like SwayAway that's the right length and with 914-4 splines... What are the differences between -4 axle assemblies and -6's? For those doing a conversion from -4 to -6, can you just use the -4 axles (assume a low hp -6 engine)? |
|
|
|
Posts in this topic
altitude411 cv joints for914/6 Dec 3 2014, 01:22 AM
type47 914 PET 501-00 #(20) shows 914.332.009.03 drive sh... Dec 3 2014, 09:35 AM gms
Can someone school me on axle shafts on a '70... Dec 3 2014, 09:55 AM peteyd I don't have a /6, but I do have all the runni... Dec 3 2014, 10:04 AM
mskala
I don't have a /6, but I do have all the runn... Dec 3 2014, 10:52 AM pcar916 I used the 914-4 axles and CV's for several ye... Dec 3 2014, 12:13 PM altitude411 Thanks to all for your input and information. I... Dec 3 2014, 01:01 PM 914Sixer Complete axles are available from Porsche for unde... Dec 4 2014, 07:22 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st August 2025 - 05:17 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.