 Anybody fab their own floor pans? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| ggenovez |
 Jan 20 2015, 09:40 AM
Post
#1
|
|
Newbie  Group: Members Posts: 19 Joined: 8-December 14 From: DFW Member No.: 18,201 Region Association: None  |
Just like the title says, anybody fabricate their own floor pans?
I have some 20ga sheet metal that I want to fabricate into floor pans. I was thinking of making a mold and using a wooden dowel to press in some ridges. If anybody has done this before and can shed some light as to how to make the molds, how deep to go, does the sheet metal overall size change... Thanks |
   |
 
|
  |
Replies
| ThePaintedMan |
Jan 20 2015, 02:08 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 3,887 Joined: 6-September 11 From: St. Petersburg, FL Member No.: 13,527 Region Association: South East States 
|
I don't think you're smoking crack to consider it. But again, you will almost surely come out on top and end up with a much nicer/easier install with the pre-formed pieces. RD makes great stuff.
You could buy the rear section from them and see if you can sources the hinges and mounts from someone cutting up a parts car. That's what I did. |
|
|
|
Posts in this topic
ggenovez Anybody fab their own floor pans? Jan 20 2015, 09:40 AM
bandjoey Restoration Design. Unless your just in love with ... Jan 20 2015, 09:53 AM
Tom_T
Restoration Design. Unless your just in love with... Jan 20 2015, 10:23 AM SirAndy With the cost of building the jigs, tools involved... Jan 20 2015, 10:38 AM mgp4591 In the process of designing them as we speak. Next... Jan 20 2015, 10:02 AM rick 918-S 20 ga? Too light.
16 ga will not bead roll.
W... Jan 20 2015, 10:23 AM mgp4591
20 ga? Too light.
16 ga will not bead roll.
... Jan 20 2015, 10:48 AM ggenovez Thanks guys.
I only need to do the rear half on b... Jan 20 2015, 12:00 PM ThePaintedMan I did just one section of floor pans on my car, mo... Jan 20 2015, 10:34 AM CptTripps Most people only need the short-rear. And for ... Jan 20 2015, 12:14 PM SirAndy Most people only need the short-rear. And for ... Jan 20 2015, 12:31 PM ggenovez If it was $100 we would not be having this di... Jan 20 2015, 01:45 PM CptTripps This kit has all you need for $350.
http://w... Jan 20 2015, 01:54 PM ggenovez Good idea George,
Where did you source your parts... Jan 20 2015, 02:18 PM toolguy Please take this as constructive. .
What is your ... Jan 20 2015, 02:16 PM ThePaintedMan Just place a WTB in the Classifieds section. There... Jan 20 2015, 02:33 PM saigon71 Post #25 and #185 shows how I fabricated pieces of... Jan 20 2015, 02:39 PM mr914 I agree, the prefab from RD is the way to go.
Som... Jan 20 2015, 06:30 PM bigkensteele Too bad you aren't closer. I have a full pass... Jan 20 2015, 06:49 PM scotty b I'm all for it. Make you own pans, keep track ... Jan 20 2015, 06:54 PM Socalandy No regrets ordering the RD pans here. Very nice pa... Jan 20 2015, 08:17 PM mgp4591 Andy, after riding in your car and seeing the work... Jan 20 2015, 08:25 PM colingreene Why is it that no one considers that while you thi... Jan 21 2015, 01:28 AM edwin Seems everyone is focused on the time and money no... Jan 21 2015, 06:21 AM mepstein On the east coast, there's usually so much to ... Jan 21 2015, 06:35 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 07:34 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.