 How to check timing on a /6 with engine in car. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| tornik550 |
 Mar 15 2015, 04:48 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,248 Joined: 29-January 07 From: Ohio Member No.: 7,486 Region Association: None  |
How do I check timing with a timing light on a /6. I know how to set the static timing however I want to check with a light. I have seen that some cut an acess panel in the firewall. I don't want to do that at this point. There isn't enough room to fit a timing light.
|
   |
 
|
  |
Replies
| fixer34 |
Mar 15 2015, 07:17 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,269 Joined: 16-September 14 From: Chicago area Member No.: 17,908 Region Association: Upper MidWest 
|
AFAIK, and how I've done it, there is an access hole on the top of the case above the flywheel. There are TDC and full advance marks on said flywheel. The hole is large enough to get a finger in there to scrape/sand away rust and put paint on the marks.
The daunting part is that you set the running timing for full advance at 6000 rpm, leaning over the carb stacks. One hand on a timing light, and one to adjust/turn the distributor. Helps to have someone in the cockpit holding the throttle at 6000 also. |
 |
|
Posts in this topic
tornik550 How to check timing on a /6 with engine in car. Mar 15 2015, 04:48 PM
Mike Bellis Pull the motor and tranny and start and time it ou... Mar 15 2015, 04:56 PM laflaur Check the timing at the flywheel. There should be ... Mar 15 2015, 05:09 PM
larryM
AFAIK, and how I've done it, there is an acce... Mar 15 2015, 08:06 PM rgalla9146 First step is to pray you have a stock flywheel.
... Mar 15 2015, 08:21 PM mskala
First step is to pray you have a stock flywheel. ... Mar 16 2015, 06:38 AM rgalla9146
First step is to pray you have a stock flywheel.... Mar 16 2015, 10:41 AM tornik550 My engine is a 2.7l with JE 9.5:1 compression pist... Mar 16 2015, 10:26 AM larryM CORRECT - just do it
even better - first static ... Mar 16 2015, 03:07 PM mskala
...
Shouldn't I simply be able to find TDC fo... Mar 16 2015, 07:34 PM r_towle Interesting,
I wonder if someone could simply glu... Mar 16 2015, 05:48 PM messix timing at 6k rpm? :screwy:
how much more advanc... Mar 16 2015, 06:02 PM mskala
timing at 6k rpm? :screwy:
how much more advan... Mar 16 2015, 07:30 PM fixer34
timing at 6k rpm? :screwy:
how much more adva... Mar 16 2015, 07:46 PM messix
[quote name='mskala' post='2161069' date='Mar 16 ... Mar 16 2015, 07:52 PM messix and it should be one of the more important things ... Mar 16 2015, 06:05 PM patssle
and it should be one of the more important things... Mar 16 2015, 07:26 PM messix nope.
please post up one.
i have a very hard tim... Mar 16 2015, 07:45 PM mskala
nope.
please post up one.
i have a very hard ti... Mar 17 2015, 08:39 AM messix soo.... it looks like even the worst one is all in... Mar 17 2015, 07:40 PM mskala
soo.... it looks like even the worst one is all i... Mar 18 2015, 08:14 AM messix
soo.... it looks like even the worst one is all ... Mar 18 2015, 06:20 PM Perry Kiehl Clone If you use a 914-6 flywheel on a 2.4 or 2.7 the ti... Mar 18 2015, 07:12 AM SLITS Jeeeze ... once I set the idle advance/retard, I b... Mar 18 2015, 08:41 AM mountainroads Reviving this old thread because I recently encoun... Aug 13 2018, 11:31 AM sixnotfour
Reviving this old thread because I recently encou... Aug 13 2018, 01:19 PM Mark Henry No access problems timing my engine :D
http://w... Aug 13 2018, 01:15 PM ClayPerrine
No access problems timing my engine :D
[img]ht... Aug 13 2018, 02:45 PM sixnotfour OTTO says....
Take dist cap off, stick car in fift... Aug 13 2018, 01:29 PM sixnotfour RE: How to check timing on a /6 with engine in car. Aug 13 2018, 01:41 PM Rand Cutting a hole isn't a problem. Leaving one is... Aug 13 2018, 03:02 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 10th May 2025 - 01:52 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.