 Brake Pedal Adjust? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| richardL |
  Sep 4 2004, 01:23 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 713 Joined: 27-January 03 From: San Diego, CA Member No.: 201 Region Association: None  |
I was trying to fit the new pedal board I have and it won't fit as it keeps binding on the brake pedal. When I played with the pedal I can move it off of the rest towards the master cylinder about 3/4" using one finger. I believe the free play should be closer to 1mm?
Anyhow it seems to me that I should be adjusting the rubber stop forwards to reduce the play - and this would move the rest position of the pedal forwards and reduce the free play and hence also the pedal board to fit in. Is that correct? or am I missing something? OK... How do I do that adjustment? I can't see any way of moving the rubber stop towards the front of the car as it is attached to the bearing tube. Essentially I am trying to stop the spring pushing the pedal up too far, but I can't see how to make that adjustment. I think I have read that the pedal height is adjustable? Hope this is clear, Thanks, Richard |
   |
 
|
  |
Replies
| richardL |
Sep 4 2004, 03:59 PM
Post
#2
|
|
Senior Member Group: Members Posts: 713 Joined: 27-January 03 From: San Diego, CA Member No.: 201 Region Association: None |
Now try the other way - attach the left hand mount screw. The board is catching in the middle on the bearing tube and the brake pedal. The right hand mount hole is way up in the air away from the hole on the cover plate. If I try to force the right hand mount in I am bending the board and the brake pedale is depressed over half an inch by the board, and I still can't get it to attach!
Attached thumbnail(s) 
|
|
|
|
Posts in this topic
richardL Brake Pedal Adjust? Sep 4 2004, 01:23 PM
davep Normally the brake pedal adjustment is done with t... Sep 4 2004, 01:49 PM richardL The brakes worked very well when I last drove it. ... Sep 4 2004, 01:58 PM Brad Roberts The brake pedal is not adjustable (just the free p... Sep 4 2004, 02:05 PM richardL Well that simplifies things.
So according to the ... Sep 4 2004, 02:12 PM davep Yes, the finger test is good. Once you start to fe... Sep 4 2004, 02:25 PM richardL I can get the board on, and I can just screw down ... Sep 4 2004, 02:40 PM Engman The pedal boards can be a little tough to get into... Sep 4 2004, 03:30 PM Brad Roberts yeah.. show us a pic.. I know you have a camera...... Sep 4 2004, 03:31 PM richardL OK, try these.
The board is on and I attach the r... Sep 4 2004, 03:57 PM richardL The clutch pedal fits fine, but notice that the bo... Sep 4 2004, 04:01 PM Engman How far off is the other mount hole?
M Sep 4 2004, 04:34 PM richardL Whichever side I attach, the board on the other si... Sep 4 2004, 04:38 PM Engman Remove the screw and mount on the lh side. Board l... Sep 4 2004, 04:54 PM richardL Mark,
If you look at the first picture I had only... Sep 4 2004, 05:16 PM richardL A few minutes with the saw and I removed that lowe... Sep 4 2004, 05:38 PM Jeroen Richard,
It's a little hard to tell by your p... Sep 4 2004, 06:12 PM Jeroen maybe the bolt for the brake stop is missing or br... Sep 4 2004, 06:13 PM richardL The nut is in place and the geometry looks like yo... Sep 4 2004, 06:24 PM Jeroen Weird...
Loosen the nuts on the MC and see if you ... Sep 4 2004, 06:37 PM Brad Roberts That is F'd up. :agree: I wonder how the MC c... Sep 4 2004, 07:07 PM richardL All looks OK... Sep 4 2004, 07:19 PM richardL Sorry about the focus... Sep 4 2004, 07:21 PM redshift The rod is properly seated?
What is up with that.... Sep 5 2004, 01:20 AM davep I don't like the looks of the master, it seems... Sep 5 2004, 12:04 PM richardL So the cluster should be flush with the floor from... Sep 5 2004, 12:21 PM Engman Pull the cluster. lets see what is in there. Shoot... Sep 5 2004, 01:13 PM richardL your wish is my command....
I pulled the cluster ... Sep 5 2004, 02:45 PM richardL and the reason I think is because of two things.
1... Sep 5 2004, 02:46 PM richardL and (2) it looks like the firewall at this point i... Sep 5 2004, 02:48 PM richardL ...inside view.... Sep 5 2004, 02:49 PM seanery looks pushed in 1/4 to 1/2" huh? Sep 5 2004, 02:49 PM richardL So...
Considering that aesthetics are not importa... Sep 5 2004, 02:52 PM richardL sgomes My 2cents is always the same 2cents: Fix it right... Sep 5 2004, 02:56 PM seanery Shannon, your avatar looks like a clown that was i... Sep 5 2004, 02:57 PM sgomes :chairfall: No, it's really me! It was f... Sep 5 2004, 03:03 PM richardL Engman Yep - its pushed in.... time for :smash: .
I am ... Sep 5 2004, 04:10 PM richardL I was able to regain about 1/4" or so (as measured... Sep 5 2004, 04:29 PM davep Well, that about settles what the problem is. Now ... Sep 5 2004, 05:58 PM richardL I had thought of a jack but I need to brace it aga... Sep 6 2004, 10:05 AM davep I would use the crossbar (front seat support) but ... Sep 7 2004, 11:10 AM
richardL I don't think the crossbar is a strong as the ... Sep 7 2004, 12:51 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th July 2025 - 04:19 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.