 Installed, floor pan deflectors |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| cpavlenko |
 Jun 23 2015, 12:31 PM
Post
#1
|
|
Member  Group: Members Posts: 489 Joined: 19-April 12 From: North Arizona Member No.: 14,400 Region Association: Southwest Region  |
Wasn't to bad, would've been much easier with a 4 post lift. I only had drive up ramps and jack stands. All went well.
  |
   |
 
|
  |
Replies
| Cevan |
Jun 23 2015, 01:56 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,079 Joined: 11-December 06 From: Western Massachusetts Member No.: 7,351 |
I'd suggest using FI clamps instead of the ones you're using as they typically have a rounded edge are less likely to cut into the rubber fuel line.
|
|
|
|
| Chris914n6 |
Jun 23 2015, 03:12 PM
Post
#3
|
|
Jackstands are my life. Group: Members Posts: 3,525 Joined: 14-March 03 From: Las Vegas, NV Member No.: 431 Region Association: Southwest Region |
QUOTE(Cevan @ Jun 23 2015, 12:56 PM)  I'd suggest using FI clamps instead of the ones you're using as they typically have a rounded edge are less likely to cut into the rubber fuel line. If they are cutting you over tightened, or the rubber hose ID is too big. |
|
|
|
Posts in this topic
cpavlenko Installed Jun 23 2015, 12:31 PM
JStroud Looks good, next upgrade I would do is replace the... Jun 23 2015, 12:43 PM cpavlenko Rubber fuel line hose through the whole car was co... Jun 23 2015, 01:02 PM 914Mels Stupid question, but what purpose do the deflector... Jun 23 2015, 02:05 PM
cpavlenko
Stupid question, but what purpose do the deflecto... Jun 23 2015, 09:27 PM cpavlenko well, it's 105 degrees out side, and I took th... Jun 23 2015, 02:56 PM screenguy914
well, it's 105 degrees out side, and I took t... Jun 23 2015, 04:28 PM cpavlenko
well, it's 105 degrees out side, and I took ... Jun 23 2015, 08:57 PM cpavlenko stock 1971 1.7. no frills. Jun 23 2015, 04:42 PM budk The plastic flaps or deflectors are to create a lo... Jun 23 2015, 06:50 PM cpavlenko
The plastic flaps or deflectors are to create a l... Jun 23 2015, 08:45 PM Garold Shaffer
The plastic flaps or deflectors are to create a ... Jun 23 2015, 08:49 PM cpavlenko
[quote name='cpavlenko' post='2201833' date='Jun ... Jun 24 2015, 01:59 PM rudedude Where did you find a set of new looking deflectors... Jun 23 2015, 07:28 PM cpavlenko
Where did you find a set of new looking deflector... Jun 23 2015, 08:51 PM Eric_Shea Don't bother taking them off. That's not y... Jun 24 2015, 08:09 AM cpavlenko
Don't bother taking them off. That's not ... Jun 24 2015, 08:58 AM rhodyguy Just release the bellows control wire at the rod a... Jun 24 2015, 08:21 AM SLITS Did you clean your on engine oil cooler?
While yo... Jun 24 2015, 08:49 AM cpavlenko
Did you clean your on engine oil cooler?
While y... Jun 24 2015, 09:00 AM rhodyguy Try ron's idea first. Jun 24 2015, 08:57 AM rhodyguy Put a catch basin on the floor under the cooler. I... Jun 24 2015, 09:08 AM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 12th March 2026 - 05:00 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.