 temp sensor |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| last337 |
 Jun 29 2015, 06:58 AM
Post
#1
|
|
Member  Group: Members Posts: 421 Joined: 4-December 12 From: New Orleans Member No.: 15,221 Region Association: None  |
Does anyone know where the temp sensor wire connects to? I cant seem to trace it down in the wiring chart. The hard coating came off but I still have the underlying wire with the spade connection at the end just cant recall where it connects.
|
   |
 
|
  |
Replies
| last337 |
Jun 29 2015, 07:37 AM
Post
#2
|
|
Member Group: Members Posts: 421 Joined: 4-December 12 From: New Orleans Member No.: 15,221 Region Association: None |
Its a '73 2.0 with dual carbs. I am referring to the wire leaving the bottom probe itself that has the metal clips on it holding it along the engine. The wire itself is only about 2' long or so then has a female spade connector on it. I found a thread about it the other day but cant find it again. I dont have anything coming off my harness that I would think went to it.
Where is the TS1 sensor? I cant find that sensor either and know I dont have anything hooked to it on the top of the motor. |
|
|
|
| BeatNavy |
Jun 29 2015, 07:39 AM
Post
#3
|
|
Certified Professional Scapegoat Group: Members Posts: 2,924 Joined: 26-February 14 From: Easton, MD Member No.: 17,042 Region Association: MidAtlantic Region 
|
QUOTE(last337 @ Jun 29 2015, 09:37 AM)  Its a '73 2.0 with dual carbs. I am referring to the wire leaving the bottom probe itself that has the metal clips on it holding it along the engine. The wire itself is only about 2' long or so then has a female spade connector on it. I found a thread about it the other day but cant find it again. I dont have anything coming off my harness that I would think went to it. Where is the TS1 sensor? I cant find that sensor either and know I dont have anything hooked to it on the top of the motor. TS1 is at the plenum near throttle body. If you're carbed TS1 and TS2 don't matter. |
|
|
|
Posts in this topic
last337 temp sensor Jun 29 2015, 06:58 AM
BeatNavy I can only speak to D-Jet. I assume you're ta... Jun 29 2015, 07:23 AM type47 Sounds like you're talking about the wire to t... Jun 29 2015, 07:43 AM
last337
Sounds like you're talking about the wire to ... Jun 29 2015, 07:46 AM BeatNavy I'm particularly good at answering the wrong q... Jun 29 2015, 07:48 AM type47 No, I was confused too since there are 3 temp sens... Jun 29 2015, 07:50 AM last337 Now if I could only get the taco plate to stop lea... Jun 29 2015, 08:01 AM Dave_Darling The grommet doesn't make a seal, if I recall c... Jun 29 2015, 09:16 AM last337 That crush washer on sender, can I get just that w... Jun 29 2015, 09:59 AM type47
... can I get just that washer ...
I did a brie... Jun 29 2015, 10:09 AM last337 Cut a gasket too.
Cut a gasket? Isnt there some... Jun 29 2015, 10:13 AM type47
Isnt there somewhere that there are printable pa... Jun 29 2015, 10:38 AM last337
Isnt there somewhere that there are printable p... Jun 29 2015, 10:40 AM type47 Yes. But 'til you find it, here's a teaser... Jun 29 2015, 10:15 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th June 2024 - 09:57 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.