 Pull type clutch question…. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Larmo63 |
 Oct 17 2015, 07:57 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 4,267 Joined: 3-March 14 From: San Clemente, Ca Member No.: 17,068 Region Association: Southern California  |
Do I need a special clutch/pressure plate for a pull type clutch system I'm assembling for my 911 conversion?
Will this work? The trans is a '70-71' I've been told. But, I'm not familiar with this stuff. Thanks for the help. http://www.ebay.com/itm/Porsche-911-65-69-...ecAAOSwhcJWFxS7 |
   |
 
|
  |
Replies
| ClayPerrine |
Oct 17 2015, 10:13 PM
Post
#2
|
|
Life's been good to me so far..... Group: Admin Posts: 16,405 Joined: 11-September 03 From: Hurst, TX. Member No.: 1,143 Region Association: NineFourteenerVille 
|
A 1975 transmission would be a 915. That clutch and pressure plate combo won't work with a 915 transmission.
If you are going to put this in a 911, just buy the 915 clutch parts. Any reputable parts house will be able to sell you the correct stuff. Besides a clutch kit, you will need a flywheel and ring gear. The ring gear is a separate part from the flywheel on the pull clutch. You also need the correct clutch cable. |
|
|
|
Posts in this topic
Larmo63 Pull type clutch question…. Oct 17 2015, 07:57 PM
euro911 Lawrence, you'll need an early 911 flywheel (... Oct 17 2015, 09:07 PM rgalla9146 Wait a minute, the trans is a '75 what ? a... Oct 17 2015, 09:17 PM euro911 The engine came out of my '67 912-6. The case ... Oct 17 2015, 09:28 PM Larmo63 Update, yes, the engine is a six bolt '69 911E... Oct 17 2015, 10:57 PM euro911 Lawrence, is this all for Speedy?
Has the diff ri... Oct 17 2015, 11:45 PM jcd914 70/71 911 pull type clutch uses a different pressu... Oct 17 2015, 11:54 PM Larmo63 Yes, it is a 911/01 tranny rebuilt with /6 gear ra... Oct 18 2015, 12:27 AM oldie914 A little history: For the 1970 911 model year, Por... Oct 18 2015, 02:19 AM rgalla9146 And now you've got all the dirt.
Enough to... Oct 18 2015, 05:25 AM ClayPerrine I have this setup in my six conversion, and have b... Oct 18 2015, 09:52 AM Larmo63 Thanks guys, at least I know what to look for now,... Oct 18 2015, 11:46 AM Mark Henry I would have used a 914 trans case*, 6 bolt '6... Oct 18 2015, 11:06 PM
stownsen914 I have the 70-71 clutch setup in my 914/6 racecar.... Oct 19 2015, 09:23 AM Larmo63 Do 914 CVs fit the 911/01 output flanges, or am I ... Oct 19 2015, 07:01 PM Mark Henry
Do 914 CVs fit the 911/01 output flanges, or am I... Oct 19 2015, 07:17 PM euro911 911 axles and CVs are larger and have 6 bolts. You... Oct 19 2015, 07:19 PM Mark Henry
I think this is the main reason so many have rec... Oct 19 2015, 08:57 PM euro911 Ah ... Mark beat me to the post - while I was stil... Oct 19 2015, 07:22 PM rgalla9146 If you go with the pull clutch it will be near imp... Oct 19 2015, 08:22 PM ClayPerrine
If you go with the pull clutch it will be near im... Oct 19 2015, 08:29 PM Larmo63 The flanges do fit the same CVs I have. I have alr... Oct 19 2015, 09:23 PM Steve Hassle wise, it is easier with a six 2.0-2.7 to us... Oct 19 2015, 11:52 PM 396
Hassle wise, it is easier with a six 2.0-2.7 to u... Oct 20 2015, 12:03 AM rgalla9146
Hassle wise, it is easier with a six 2.0-2.7 to u... Oct 20 2015, 05:42 AM Mark Henry
Just to clarify, the '70-'71 trans fro... Oct 20 2015, 05:39 PM Larmo63 Yes, I mis-identified it earlier as a 901/01. My t... Oct 20 2015, 04:18 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 20th June 2025 - 09:50 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.