 CV's, replace or rebuild |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Amphicar770 |
 Jan 2 2016, 11:36 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,216 Joined: 20-April 10 From: PA, USA Member No.: 11,639 Region Association: MidAtlantic Region 
 |
Hi All,
Looks like I need to replace the CV's on my '74 2.0. I can slide both axles easily from side to side creating the banging noise I was trying to diagnose. I can get two new axle assemblies from Porsche for about $575 with shipping or I can get a set of these from Racer Chris for about $500 ... New Lobro German Type 1 CV Joints adapted for use in 914 rear axle assemblies. Are the Lebro's any better than the original CV joints? COst between the two is close enough that I will go with whatever is better. If the same, I will just get the new ones as there is less to take apart. Thx. Mike |
   |
 
|
  |
Replies
| brant |
Feb 16 2016, 11:14 PM
Post
#2
|
|
914 Wizard Group: Members Posts: 11,951 Joined: 30-December 02 From: Colorado Member No.: 47 Region Association: Rocky Mountains 
|
Can you show a side by side picture of a new joint next to an old one?
I wonder if they happen to be stronger/larger than old stock joints |
|
|
|
Posts in this topic
Amphicar770 CV's, replace or rebuild Jan 2 2016, 11:36 AM
Tom_T If it were me, I'd pop for the extra $75 ... Jan 2 2016, 12:32 PM
mskala
...
The original Porsche Type IV's CVs on the... Jan 4 2016, 03:29 PM Amphicar770 Thanks Tom. Just ordered the new ones. Of course... Jan 2 2016, 12:39 PM 914Sixer Porsche had the axles made up. GKN/Lobo has gotte... Jan 2 2016, 03:18 PM Mark Henry You can at least see if any of your CV's are s... Jan 2 2016, 03:33 PM porschetub
You can at least see if any of your CV's are ... Feb 17 2016, 01:53 AM whitetwinturbo :confused: .....so how much side-to-side is ok bef... Jan 2 2016, 09:17 PM Amphicar770
:confused: .....so how much side-to-side is ok be... Jan 4 2016, 11:33 PM whitetwinturbo
:confused: .....so how much side-to-side is ok b... Jan 5 2016, 11:58 AM stinkindiesel I'm in the same boat, and I'm really confu... Jan 4 2016, 02:40 PM mskala
...
When I look at replacement CV joints, though,... Jan 4 2016, 03:26 PM 914Sixer Just buy new axle assemblies and get the Porsche w... Jan 4 2016, 06:09 PM 76-914 Not a bad idea to flip 'em if you do re-use th... Jan 4 2016, 06:41 PM Amphicar770 Looks like the new complete axles are indeed, avai... Jan 7 2016, 10:10 AM Amphicar770 New axles came in. Looks like they are indeed mad... Jan 9 2016, 01:29 PM Kansas 914
New axles came in. Looks like they are indeed ma... Jan 9 2016, 02:46 PM maddin
New axles came in. Looks like they are indeed ma... Feb 17 2016, 03:08 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th May 2025 - 04:34 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.