 Heater cables needed |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Racer |
 Oct 13 2016, 02:14 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 787 Joined: 25-August 03 From: Northern Virginia Member No.: 1,073 Region Association: MidAtlantic Region  |
It was a little chilly recently while out on a ride in my -6. Pulled up the red lever for heat and got none. This was odd because as a kid, I recall the car always putting out a little heat, even in summer. Well, after I crawled underneath, I noticed that someone had removed the heater cables from the control boxes. Hmm. That may have been fine in Florida but not so great here.
Where do folks source heat cables from? I am not sure how much of the system I need to replace, but assume its the main cables and ends. Are they the same for -4 and -6 cars? Do they come in sets or individually (for each side)? I presume my control boxes actually work in this scenario (IMG:style_emoticons/default/wink.gif) TIA (IMG:style_emoticons/default/wavey.gif) |
   |
 
|
  |
Replies
| Mikey914 |
Oct 13 2016, 05:02 PM
Post
#2
|
|
The rubber man Group: Members Posts: 12,677 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None 
|
Got them in stock with protective coating, plug and play. You can make your own, but by the time you buy the wire, and then you are crimping the bolt on the barel net will fatigue the wire and you'll get to do it again, but bright side you already have cable to do it again.
http://shop.914rubber.com/PCG42407501-914-...m?categoryId=-1 |
|
|
|
Posts in this topic
Racer Heater cables needed Oct 13 2016, 02:14 PM
76-914 Check with Mark at 914rubber. I sent him a pristin... Oct 13 2016, 02:18 PM DavidSweden
It was a little chilly recently while out on a ri... Oct 13 2016, 02:48 PM sbsix Racer check with Mark at 914Rubber. I measured my ... Oct 13 2016, 04:55 PM
Racer
Got them in stock with protective coating, plug a... Oct 13 2016, 06:22 PM BeatNavy
[quote name='Mikey914' post='2410875' date='Oct 1... Oct 13 2016, 07:26 PM Racer Thanks. Going to try 914Rubber as suggested. Order... Oct 14 2016, 03:54 PM Mikey914 Thanks for responding, he's correct, the cable... Oct 14 2016, 05:48 PM Racer Ok.. Now that the parts arrived.. I thought I cou... Oct 19 2016, 04:25 PM pbanders RE: 914 heater output - I've always found it t... Oct 19 2016, 08:49 PM Mikey914 Tried to find a better shot, but they just come ou... Oct 19 2016, 11:51 PM Racer Thanks! Oct 20 2016, 03:58 PM Racer Its bad to reconnect just one side, correct?
I wa... Oct 25 2016, 05:52 PM Mikey914 I wouldn't say it would be "bad". Wo... Oct 25 2016, 05:58 PM mepstein I don't think it will work just pulling from o... Oct 25 2016, 05:58 PM cwpeden I've had only one for 10 years. Not a problem. Oct 25 2016, 07:04 PM Mikey914 The bend in the wire is significant so hard to say... Oct 25 2016, 09:18 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd June 2024 - 02:15 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.