 Weltmeister oil trap. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Keith914 |
 Mar 14 2017, 09:34 PM
Post
#1
|
|
Member  Group: Members Posts: 248 Joined: 29-April 16 From: Laguna Beach, California 92651 Member No.: 19,948 Region Association: Southern California  |
I attempted to install this new Weltmeister sump oil trap today, but concluded it cannot be installed with the existing stock oil screen. Is this correct? Otherwise I believe installation of this oil trap replaces both the screen and taco plate -- from the top down: O ring, pickup extension, taco plate size gasket, oil trap, copper squash washer, bolt, all shown in the pic, correct?
Attached image(s) 
|
   |
 
|
  |
Replies
| falcor75 |
Mar 14 2017, 11:17 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,579 Joined: 22-November 12 From: Sweden Member No.: 15,176 Region Association: Scandinavia 
|
Be very carefull tightening the bolt.....you dont want type4 syndrome.
|
|
|
|
| Mark Henry |
Mar 15 2017, 06:33 AM
Post
#3
|
|
that's what I do! Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada |
QUOTE(falcor75 @ Mar 15 2017, 01:17 AM)  Be very carefull tightening the bolt.....you dont want type4 syndrome. (IMG:style_emoticons/default/agree.gif) and the tuna can makes over tightening even easier. Get a proper inch pound torque wrench, without it use your shortest 1/4" ratchet and tighten with one finger only. |
|
|
|
Posts in this topic
Keith914 Weltmeister oil trap. Mar 14 2017, 09:34 PM
Dave_Darling Correct. The instructions should mention omitting... Mar 14 2017, 10:29 PM brant On those welt kits I have also opened the oil slot... Mar 14 2017, 10:36 PM Keith914 Thanks for all of your comments. I will open up th... Mar 15 2017, 08:49 AM Dave_Darling Nine. As in, less than 10 lb-ft. That's why ... Mar 15 2017, 09:50 AM
Keith914
Nine. As in, less than 10 lb-ft. That's why... Mar 15 2017, 10:11 AM Mark Henry So that would be 108 inch pounds. An inch pound to... Mar 15 2017, 11:41 AM RobW Over clean the area and mount it straight. +3 on t... Mar 15 2017, 12:09 PM maf914 :hijacked:
Can anyone recommend a good inch-poun... Mar 15 2017, 04:09 PM mgphoto
:hijacked:
Can anyone recommend a good inch-pou... Mar 15 2017, 07:26 PM old914dog Drill for safety wire......it doesn't cost muc... Mar 15 2017, 07:45 PM tjtryon I know, I know, I'm resurrecting an old post.
... Oct 26 2020, 11:01 AM 914werke While this part doesn't exist anymore there ar... Oct 26 2020, 01:50 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 16th June 2024 - 01:16 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.