 Uncharted Territory, Clutch Replacement |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| loco914 |
 Apr 21 2018, 09:13 PM
Post
#1
|
|
Thy wheels have left the rail...  Group: Members Posts: 47 Joined: 1-April 10 From: Amarillo, TX Member No.: 11,542 Region Association: None  |
First engine/tranny drop was successful.
 Pulled the clutch and found this...   The adventure begins... |
   |
 
|
  |
Replies
| GeorgeRud |
Apr 21 2018, 10:18 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 3,725 Joined: 27-July 05 From: Chicagoland Member No.: 4,482 Region Association: Upper MidWest |
I think you got your money’s worth out of those parts as the pressure plate definitely is worn out and the springs gave up in the clutch plate. Don’t forget to take the chance to clean the engine compartment and engine while it’s out as it’s a lot easier than when it’s installed.
|
|
|
|
Posts in this topic
loco914 Uncharted Territory Apr 21 2018, 09:13 PM
porschetub That's messy,don't often see a disk do tha... Apr 22 2018, 02:04 AM Porschef Throw in some SS fuel lines while the engine's... Apr 22 2018, 06:23 AM loco914 Here’s the flywheel. Plan to remove and have it ... Apr 22 2018, 12:12 PM
porschetub
Here’s the flywheel. Plan to remove and have it... Apr 22 2018, 06:00 PM loco914 Just don’t understand why it would run hot.... :... Apr 22 2018, 12:41 PM Superhawk996
Just don’t understand why it would run hot.... ... Apr 12 2020, 02:22 PM 98101 Going to do my clutch (pushrod tube seals, rear ma... Apr 22 2018, 01:42 PM loco914
Going to do my clutch (pushrod tube seals, rear m... Apr 22 2018, 03:59 PM loco914 Ok. This is hopefully as far as I will go.
... Apr 22 2018, 05:04 PM rgalla9146
Ok. This is hopefully as far as I will go.
... Apr 22 2018, 05:30 PM nditiz1 Not trying to hijack, but can someone tell me how ... Apr 22 2018, 05:38 PM Andyrew
Not trying to hijack, but can someone tell me how... Apr 23 2018, 11:55 AM Perry Kiehl You are going to run much cooler with all the moto... Apr 22 2018, 07:16 PM loco914 Thanks for all the tips! Keep them coming. It ... Apr 22 2018, 09:42 PM Dr Evil Don't forget the TOB and to see if you need to... Apr 23 2018, 09:02 AM loco914 A little progress last night and today. Got the mu... May 5 2018, 06:55 PM porschetub A good clean on the housing you will be good,if yo... May 5 2018, 11:56 PM Amphicar770 Fun stuff. Did mine about a year ago.
There are... May 6 2018, 09:30 AM Amphicar770 Regarding oil cooler. They are not expensive. I go... May 6 2018, 09:53 AM loco914
Regarding oil cooler. They are not expensive. I g... May 7 2018, 12:45 PM loco914 Slow, but making progress. Estimating the equivale... May 12 2018, 01:11 PM cuddy_k Steam cleaner. Under 100 bucks at HF.
https://ww... May 12 2018, 02:08 PM 1adam12 I just finished cleaning my engine up. Took about... May 12 2018, 03:02 PM loco914 Very nice! Much needed motivation. May 12 2018, 04:09 PM Mark Henry http://www.914world.com/bbs2/uploads/post-11542-15... May 12 2018, 04:12 PM loco914 Almost 2 years to the day, I finally have my 914 b... Apr 12 2020, 02:18 PM loco914 Before. Apr 12 2020, 02:30 PM loco914 Before. Apr 12 2020, 02:32 PM loco914 After. Apr 12 2020, 02:33 PM loco914 Before. For the 3rd time. Apr 12 2020, 02:34 PM loco914 Rebuilt pedal board. Apr 12 2020, 02:38 PM loco914 Ready to install Apr 12 2020, 02:39 PM loco914 All buttoned up. Apr 12 2020, 02:40 PM loco914 Off the ramps and ready to roll, :driving: Apr 12 2020, 02:41 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 11th July 2025 - 05:12 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.