 tool tow hook, any interest? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| dr914@autoatlanta.com |
 Jul 10 2018, 08:23 AM
Post
#1
|
|
914 Guru  Group: Members Posts: 8,188 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None  |
we have this being duplicated now and wonder how much interest there is. Molding is quite expensive on this part so we would have to sell for 35 bucks but it would be an exact zinc plate duplicate
Any interest? |
   |
 
|
  |
Replies
| Mikey914 |
Jul 13 2018, 12:16 PM
Post
#2
|
|
The rubber man Group: Members Posts: 12,772 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None 
|
Soak it with penetrating oil and let sit for an hour or so to let it weep into the areas it can. Use a smaller bit to make a pilot hole and go to town with the largest bit you feel comfortable with (as not to damage the threads).
Mark |
|
|
|
Posts in this topic
dr914@autoatlanta.com tool tow hook Jul 10 2018, 08:23 AM
rhodyguy Are they 'sand cast' or permanent mold tem... Jul 10 2018, 08:29 AM
dr914@autoatlanta.com no not sand cast
Are they 'sand cast' o... Jul 10 2018, 08:47 AM Sprovost Interested, I’ve been looking for one as mine br... Jul 10 2018, 09:30 AM Eric_Shea
Interested, I’ve been looking for one as mine b... Jul 10 2018, 09:35 AM rhodyguy Will The TOTAL shipping for this part be $7.0... Jul 10 2018, 09:37 AM scallyk9
Will The TOTAL shipping for this part be $7.... Jul 10 2018, 04:36 PM jdamiano
Will The TOTAL shipping for this part be $7... Jul 10 2018, 04:52 PM Retroracer interested,
- Tony Jul 10 2018, 09:50 AM jdamiano I would buy one to use if needed not to ruin my or... Jul 10 2018, 12:16 PM 914Sixer I am good for one. Jul 10 2018, 05:58 PM mb911 Are you sure they weren't drop forged? Pretty ... Jul 10 2018, 06:00 PM Mikey914 They were at forged part. That's one of the re... Jul 10 2018, 06:12 PM sixnotfour and they break if you pull any angle other than st... Jul 10 2018, 06:19 PM Mark Henry
and they break if you pull any angle other than s... Jul 10 2018, 08:06 PM Larmo63 They work in a pinch, I wouldn't bet my life o... Jul 10 2018, 06:59 PM type2man Keep your 914 in check and drive it often and you... Jul 10 2018, 07:28 PM campbellcj Mine broke-off too and I've been unable to get... Jul 10 2018, 07:57 PM Mikey914
Mine broke-off too and I've been unable to ge... Jul 12 2018, 03:37 PM campbellcj
Mine broke-off too and I've been unable to g... Jul 13 2018, 10:52 AM Hans Jan I need one.
If the original design is not good eno... Jul 10 2018, 08:26 PM Mark Henry
I need one.
If the original design is not good en... Jul 10 2018, 09:55 PM mb911 Is it flush with the end? You could weld a nut on ... Jul 13 2018, 11:29 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 13th July 2025 - 05:30 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.