![]() |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
![]() |
rstover |
![]()
Post
#1
|
Member ![]() ![]() Group: Members Posts: 136 Joined: 15-November 11 From: Kerrville, TX Member No.: 13,785 Region Association: Southwest Region ![]() |
I am guessing some type of mineral oil The picture is a tit that has started to rust but other wise is in good condition. I believe that vegetable will not harm rubber so I have given this tit a good shot of Walnut Oil that was past the expiration date for consumption.
![]() |
![]() ![]() |
dr914@autoatlanta.com |
![]()
Post
#2
|
914 Guru ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 7,900 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None ![]() |
that is because the rubber material was not water proof and the spine was made from mild steel. Since the factory discontinued them we had them made but with waterproof factory look material and stainless spine.
No one cared that the vw produced 914 would be around 40 years later so did not use the best materials available. Too bad, there would be a lot more of the cars around if they had,. The 914 ended just one year before they started to galvanize the bodies. What if.... I am guessing some type of mineral oil The picture is a tit that has started to rust but other wise is in good condition. I believe that vegetable will not harm rubber so I have given this tit a good shot of Walnut Oil that was past the expiration date for consumption. ![]() |
ClayPerrine |
![]()
Post
#3
|
Life's been good to me so far..... ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Group: Admin Posts: 15,541 Joined: 11-September 03 From: Hurst, TX. Member No.: 1,143 Region Association: NineFourteenerVille ![]() ![]() |
that is because the rubber material was not water proof and the spine was made from mild steel. Since the factory discontinued them we had them made but with waterproof factory look material and stainless spine. No one cared that the vw produced 914 would be around 40 years later so did not use the best materials available. Too bad, there would be a lot more of the cars around if they had,. The 914 ended just one year before they started to galvanize the bodies. What if.... I am guessing some type of mineral oil The picture is a tit that has started to rust but other wise is in good condition. I believe that vegetable will not harm rubber so I have given this tit a good shot of Walnut Oil that was past the expiration date for consumption. ![]() I always hope some energetic soul with the proper skill level would make a 914 body, doors, engine lid, and trunk lids in carbon fiber. Put a vin from a chassis that is beyond saving on it, and paint it up. If it is done right, you would have a rust free 914 forever!! |
DRPHIL914 |
![]()
Post
#4
|
Dr. Phil ![]() ![]() ![]() ![]() ![]() Group: Members Posts: 5,769 Joined: 9-December 09 From: Bluffton, SC Member No.: 11,106 Region Association: South East States ![]() ![]() |
that is because the rubber material was not water proof and the spine was made from mild steel. Since the factory discontinued them we had them made but with waterproof factory look material and stainless spine. No one cared that the vw produced 914 would be around 40 years later so did not use the best materials available. Too bad, there would be a lot more of the cars around if they had,. The 914 ended just one year before they started to galvanize the bodies. What if.... I am guessing some type of mineral oil The picture is a tit that has started to rust but other wise is in good condition. I believe that vegetable will not harm rubber so I have given this tit a good shot of Walnut Oil that was past the expiration date for consumption. ![]() i saw somewhere recently an ad for a company that is making a 911 993 body in carbon fiber -wonder what that cost! i doubt you will see them expand into the 914 arena but it would be cool, though most of us could not afford it anyway. I always hope some energetic soul with the proper skill level would make a 914 body, doors, engine lid, and trunk lids in carbon fiber. Put a vin from a chassis that is beyond saving on it, and paint it up. If it is done right, you would have a rust free 914 forever!! |
![]() ![]() |
![]() |
Lo-Fi Version | Time is now: 17th June 2024 - 06:16 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |